Craftsman 917.271641 Install Seat, Release parking brake by depressing clutch/brake pedal

Page 9

Label

Batter

Door

INSTALL SEAT

Adjust seat before tightening adjustment knob.

1, Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

2, Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

3.Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

4.Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

5.Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

6.Lower seat into operating position and sit in seat.

7.Slide seat until a comfortable position is reeched which allows you to press clutch/brake pedal all the way down.

8.Get off seat without moving its adjusted position.

9.Raise seat and tighten adjustment knob securely.

\

Seat Pan_.

Bolt

Flat

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLLTRACTOR OFF SKID (See Operation section for location and function of controls)

1.Press lift lever plunger and raise attachment lift lever to its highest position.

2.Release parking brake by depressing clutch/brake pedal.

3.Place freewheel control in freewheel-

ing position to disengage transmis- sion (See "TO TRANSPORT" in the

Operation section of this manual).

4.Roll tractor forward off skid.

5.Remove banding holding deflector shield up against tractor.

TO DRIVETRACTOR OFF SKID (See Operation section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in

the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of

other people and objects.

1.Be sure all the above assembly steps have been completed.

2.Check engine oil level and fill fuel tank with gasoline.

3.Place freewheel control in "transmis- sion engaged" position.

4.Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

5.Place motion control lever in neutral

(N)position.

6.Press lift lever plunger and raise attachment lift lever to its highest position.

7.Start the engine. After engine has started, move throttle control to idle position.

8.Release parking brake.

9.Slowly move the motion control lever forward and slowly drive tractor off skid.

10.Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

11.Turn ignition key to "OFF" position. Continue with the instructions that follow.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents ICRnFT Mrwi Safety Limited 90 DAY Warranty on BatteryBack Cover General Operation II. Slope OperationDo not IlL Children IV. ServicePage Amps Headlights ProductspecificaonsRepair Agreement Customer ResponsibilitiesSteering WheelInsert Tools Required for Assembly Howto SET UpyourtractorTo Removetractor from Carton Unpack Carton Release parking brake by depressing clutch/brake pedal Install SeatInstall Mulcher Plate @@@@@ Knowyourtractor Howto Useyourtractor To SET Parking Brake To Adjust Mower Cutting HeightTo USE Throttle Control To Move Forward and BackwardTo Transport To Operate MowerTo Operate on Hills MentsADD Gasoline Before Startingthe Engine Check Engine OIL LevelTo Start Engine Move throttle control to choke positionAutomatic Transmission Warm UP PurgetransmissionMulching Mowingtips MowingtipsMaintenance Schedule Lubrication ChartGeneral Recommendations Before Each USETractor BatteryTires Operator Presence SystemTransaxle Cooling BeltsTransaxle Pump Fluid Engine LubricationSpecifications Clean AIR ScreenTo Service PRE-CLEANER Engine Cooling FinsTo Install Mower CleaningTractor To Remove MowerMower to SIDE-TO-SIDE AdjustmentGround Tighten nut E on both front links an equa number of turnsTo Replace Mower Blade Drive Belt To Adjust BrakeDepress clutch/brake pedal and engage parking brake Becomes 1-9/16. Retighten jam nut against nut aTo Adjust Steering Wheel ALIGN- Ment Transaxle Motion Control Lever Neutral AdjustmentTo Start Engine with a Weak Battery Transmission REMOVAIJREPLACE- MentTo Replace Headlight Bulb Replacing BatteryInterlocks and Relays To Replace FuseTo Adjust Carburetor To Adjust Throttle Control CablePreliminary Setting EngineAcceleration Test Engine OIL Engine Fuel SystemCylinders OtherTroubleshooting Chart Problem CauseCorrection Problem Problemcause Tractor --MODEL Number SchematicElectrical Tractor --MODEL Number 917,271641Electrical Tractor --MODEL Number 917.271641 Chassis and Enclosures Bolt, Carriage Tractor - Model Number 917.271641 Chassis and EnclosuresIhal I UII- MUUI-LNUNIt-II 11f.Z/1t41 25/32 TRACTOR--MODEL Number Ground DriveTractor - Model Number 917.271641 Steering Assembly TRACTOR--MODEL Number Steering AssemblyTractor - Model Number 917,271641 Optional EquipmentSpark Arrester Inch= 25,4 mm HA. I UH - Muuil NU MII- H Seat AssemblyWheels &TIRES Decals3219 Lift AssemblyTractor -- Model Number Lift Assembly 917.271641 TRACTOR--MODEL Number Mower DeckKEY Part Description Tractor --MODEL Number Mower DeckTractor - Model Number Hydro Transaxle - Model Number ID X 40MM Specialtools To NSTALL. see Repair Instruct On Manual ++ l LABEL*EMISSIONS 462 801287 524Tractor - Model Number 15`692226 TlA., tuft - MULJt. NUMtH 917,27141Fan-Flywheal Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ours
Top Page Image Contents