ASSE BLY
HOW TO SET UP YOUR TRACTOR
PREPARE BATTERY (See Fig. 2)
i llll i,. | , i ,, i ,m i ,t=_,,,, |
CAUTION: Wear eye and face shield,
Wash hands or clothing Immediately if accldentallyln contact with battery actd.
Do not smoke. Fumes from charged battery acld are explosive.
Read the Instructions Included with the battery vent caps. Alwayswear gloves, clothing and goggles to protect your hands, skin and eyes.
Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger wili extend its life.
"See instructions packed with vent caps in parts bag.
,Fill battery with acid. Fill each cell until it reaches the bottom of the vent we{Is. Do not overfill.
•Ailow battery to stand and settle for at least thirty
minutes. After standing, check the _evel of acid. If
INSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment bolt.
°Remove cardboard packing on seat pan.
Place seat on pan and assemble shoulder bolt.
. Assemble adjustment bolt, lock washer and flat washer loosely. Do not tighten.
•Tighten shoulder bolt securely.
,Lower seat into operating position and sit on seat.
. | SIide seat until a comfortable position is reached which |
| aIIows you to press clutch/brake pedal all the way down |
| (See Fig. 6). |
•Get off seat without moving its adjusted position.
,Raise seat and tighten adjustment bolt securely.
SEAT PAN
SHOULDER
BOLT
below the vent wells, add more acid until the correct level is reached.
While battery is standing (after adding acid) and later, while battery isbeing charged, continue with assembly of tractor.
IMPORTANT: TO MAXiMiZE THE LIFE OF YOUR
BATTERY, IT IS NECESSARY THAT THE BATTERY BE CHARGED BEFORE USE FAILURE TO CHARGE
BATTERY CAN RESULT {N A SHORTENED BATTERY LiFE
•Charge battery at a rate of 6 amperes for 1 hour. Use
oFLAT WASHER
ADJUSTMENT | " LOCK WASHER |
BOLT |
|
a 12volt battery charger. Observe all safety precautions required for battery charging.
. Check the acid level after the battery is charged, If the acid has fallen below the correct level, add distilled or iron free water.
. Install the vent caps to cover the vent weIIs. Wash the top of the battery with water to remove any acid, then wipe dry,
•Check battery case for leakage to make sure that no damage has occurred in handling.
•Dispose of excess battery acid, Neutralize acid for disposal by adding it to four inches of water in a five
gallon plastic container. Stir with a wooden or plastic paddle white adding baking soda until the addition of more soda causes no more foaming,
o Follow instructions on how to install battery.
FIG, 3
CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.
. Reduce tire pressure PSI shown in "PRODUCT SPECIFICATION on page 3 of this manual.
CHECK DECK LEVELNESS
For best cutting results, mower housing should be properly leveled. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.
CHECK FOR PROPER POSITION OF ALL BELTS
CUTAWAYVIEW | j VENTCAP |
j | w. W LL |
See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.
_ |
|
| BATTERY | CHECK BRAKE SYSTEM |
|
|
|
| |
t _ | r_ _ r.,'J r_/f_t | CELLAClD | After you learn how to operate your tractor, check to see | |
|
|
|
| |
|
|
|
| that the brake is properly adjusted. See "TO ADJUST |
|
|
|
| BRAKE" in the Service and Adjustments section of this |
|
| F1Go2 | 8 | manual |
|
|
|