Manuals / Teledyne / TV and Video / TV Converter Box

Teledyne 4060 manual Note Before setting up an AUTOCAL, be sure you understand, Linearization

Models: 4060

1 79

Download 79 pages 47.82 Kb

Page 56

Operation	Series 4060

______________________________________________

-> CH1 Offset

CH1 Gain

CH1 (Wave, Id for Ch2, or Group Output)

CH1 (Select Groups)

CH2 (Wave, Id for Ch2, or Group Output)

CH2 (Select Groups)

______________________________________________

4.6.12 Linearization

Not applicable to the 4060 configuration.

4.6.13 Changing Stream

Affects the relay on the rear panel that controls which gas is allowed to flow to the column and detector.

When the instrument has electronically controlled calibration valves (option), the gas stream can be switched here. You can flow span, sample (or zero gas) without entering the calibration mode in order to check instrument response. During a span calibration, the span stream is activated. After a span calibration, the sample stream is activated regardless of what was set before the span.

4.6.14 Setting up an AUTO-CAL

The Series 4060 Analyzer can be fitted with an external auto calibration module as an option. This feature provides automatic switching of sample and calibration gases and allows the operator to program calibration events to occur automatically

Note: If your instrument is not fitted with an autocal module, the autocal screens will still appear on the display but will be non-functional.

Note: Before setting up an AUTOCAL, be sure you understand

56	Teledyne Analytical Instruments

Image 56

Teledyne 4060 manual Note Before setting up an AUTOCAL, be sure you understand, Linearization, Changing Stream

Contents

DANGER INSTRUCTION, OPERATING AND MAINTENANCE MANUAL FORSERIES P/N M76417 DATE 06/29/10Warranty SeriesTeledyne Analytical Instruments Copyright 2010 Teledyne Analytical InstrumentsSafety Messages No SymbolThis manual provides information designed to guide you through the installation, calibration and operation of your new analyzer. Please read this manual and keep it available DANGER Additional Safety InformationCOMBUSTIBLE GAS USAGE Always purge the entire system before performing any maintenance and always leak check the system after removing any tubing or fittings on the sample system. See the procedures for purging and leak checking this instrument on the following pages Procedure for Removal of Internal Inaccessible Shock Hazards READ THIS MANUAL BEFORE OPERATING THE INSTRUMENT AND ADHERE TO ALL WARNINGS INCLUDED IN THIS MANUALTable of Contents 3.3 User Connections 4.5 Sample Pump 5.1.4 Collector Cable List of Figures Figure 2-1 Internal Temperature ControllersFigure 2-2 Typical Piping Diagram for the Model Figure 3-2 Equipment Interface Connector Pin ArrangementList of Tables Table 3-4 Alarm Relay Contact PinsTable 3-7 Pin out of 50 pin D-Sub Connector Table 3-8 Commands via RS-232 Input1.1 Main Features of the Analyzer Introduction1.2 Principle of Operation 1.3 Analyzer DescriptionFigure 1-1 Model 4060 Front Panel Interface Figure 1-2 Model 4060 Rear PanelSeries Introduction Detecting atmospheric pollutants 1.4 Applications Gas purity certification  Detecting trace benzene in ambient air 2.2 Modes of Operation Operational Theory2.1 Introduction 2.3 Analyzer Subsystems 2.3.1 Sample SystemFigure 2-1 Internal Temperature Controllers 2.3.2 Gas Flow Control System2.3.3 Fuel and Blanket Air Systems 2.3.4 Flame Ionization Detection CellFigure 2-2 Typical Piping Diagram for the Model SeriesOperational Theory Teledyne Analytical Instruments2.4 Detection Cell Figure 2-3 Flame Ionization Cell 2.4.1 Electrometer-Amplifier2.4.4 Flame Ignition Circuit 2.4.2 Anode Power Supply2.4.3 Flame Guard Circuit 3.2 Mounting the Analyzer Installation3.1 Unpacking the Analyzer 3.3.2 Electronic Connections 3.3 User Connections3.3.1 Electrical Power Connections Figure 3-1 Model 4060 Rear Panel with Optional Gas Manifold 3.3.2.1 PRIMARY INPUT POWERFigure 3-2 Equipment Interface Connector Pin Arrangement 0-1 VDC % of RangeTable 3-1 Analog Output Connections Table 3-2 Analog Concentration Output-ExamplePin Function ExamplesTable 3-3 Analog Range ID Output-Example Threshold AlarmTable 3-4 Alarm Relay Contact Pins Table 3-5 Remote Calibration Connections For exampleTable 3-6 Range ID Relay Connections 2. When the CRC closes, remove the span commandTable 3-7 Pin out of 50 pin D-Sub Connector 3.3.2.10 RS-232 PORT3.3.3 Gas Connections Table 3-8 Commands via RS-232 InputTable 3-9 Required RS-232 Options Figure 3-3 Gas Connections USE WATER PUMPED AIR WITH THC LESS THAN 0.1 PPM. DO NOT USE OIL PUMPED AIR UNDERANY CIRCUMSTANCES FUEL3.4 Placing the System in Operation Operation 4.1 Equipment4.2 Preliminary Power-Off Check List 4.3 Activating the Support Gases4.4 Flame Ignition 4.3.1 Air4.3.2 Carrier Gas 4.3.3 Span Gas4.5 Sample Pump 4.6 Analyzer Operation4.4.1 Verification of the Flame Guard Circuit 4.4.2 Ignition and/or Flame Guard Circuit FailureCaution ALARM SUPPRESSION Refer to the Addendum and Testing 4.6.1 Default ParametersAlarms PasswordExample Analysis Mode or Setup Mode4.6.3 Navigation and Data Entry 4.6.3.2 ENTER4.6.3.3 ESCAPE 4.6.4 Menu Structure3. MODIFIABLE ITEM screens have a flashing value somewhere in the line 4.6.5 Span Note The self diagnostics will interrupt analysis temporarily 4.6.8 System Self-Diagnostic Test4.6.6 ALT-SPAN 4.6.7 The Model Screen4.6.9 The Alarms Function AL-2 50.00 ppb AL-1 DEFEATED AL-1 HIGH AL-1 NON-FAILSAFE AL-1 NON-LATCHINGAL-1 20.00 ppb AL-2 ACTIVE AL-2 LOW AL-2 FAILSAFE AL-2 LATCHING RELEASING A LATCHED ALARM When alarm conditions are present, the main analysis screen will have one or both of the following messages AL-1, AL-2 followed by the instruction ENT/ACK . Pressing ENTER will release a latched alarm. That is, if there will not be an alarm condition until the analysis concentration is again violating the trip point. Furthermore, the alarms will be suppressed until the analysis value is updated, so even though the screen may be reporting a value that should cause an alarm, until the analyzer again enters SAMPLE MODE, no alarm condition will reoccur 4.6.11 Analog Output Adjustment 4.6.10 The Range FunctionRange Select Man Man Rng R1 R1 0-100.00ppb R2 0- 1.00ppm R3 0- 10.00ppmNote Before setting up an AUTOCAL, be sure you understand 4.6.14 Setting up an AUTO-CAL4.6.12 Linearization 4.6.13 Changing StreamAUTOCAL PASSWORD AS3d 20h AUTO SPAN Enabled Span in 11 days Span in 6 hours4.6.15 Timing 4.6.16 Group Setup4.6.17 Password Protection ENTERING A PASSWORD PASSWORDENTER NEW PASSWORD SCREEN ENTER PASSWORD SCREENCHANGE PASSWORD SCREEN REPEAT PASSWORD ENTRY SCREEN 4.6.18 Logging OutRestrict Access? ENTER=Yes ESCAPE=NO 4.6.19 StandbyEnter Pressing Enter places the instrument in STANDBY Teledyne Analytical Instruments OperationSeries Maintenance & Troubleshooting Work with one hand only5.1 Measuring Circuit Electrical Checks 5.1.1 Anode Voltage Check5.1.3 Printed Circuit Board Replacement 5.1.2 Electronic Stability5.2 Temperature Control Electronic Check 5.1.4 Collector Cable5.3 Ignition and/or Flame Guard Circuit Checks 5.4 Sampling System 5.5 Printed Circuit Board Descriptions 5.5.1 Flame Guard and Anode Power Supply PCB5.5.2 Proportional Temperature Controller PCB 5.5.3 Electrometer-Amplifier PCB The stability of the electrometer circuit can be tested as follows A.1 Specifications and Initial Settings AppendixA.2 Recommended Spare Parts List Analytical InstrumentsA.3 Drawing List PC Board AssembliesTeledyne Analytical Instruments AppendixSeries B1 Addendum and Testing Results Appendix B