Craftsman 917.25736 owner manual Mowing Tips

Page 13

OPERATION

TO START ENGINE (See Fig. 7)

When starting engine for the first time or if engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

Depress the clutch/brake pedal and set the parking brake

Place motion control lever in "NEUTRAL" position.

Move attachment clutch to "DISENGAGED" position.

Move throttle control lever to "CHOKE" position for cold engine start. For warm engine start, move throttle control to "FAST" position.

Turn ignition key clockwise to "START" position and release key as soon as engine starts Do not run

starter continuously for more than fifteen seconds per minute. If engine does not start after several attempts, move throttle control to "FAST" position, wait a few minutes and try again

When engine starts, slowly move throttle control lever to desired running speed.

Al!ow engine to warm up for a few minutes before engaging motion control or attachment clutch

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 ° F), the carburetor fuel mixture may need to be adjusted for best engine performance. See "TO ADJUST CARBURETOR" in the Service and Adjust- ments section of this manual

MOWING TIPS

Tire chains cannot be used when the mower housing is attached to unit.

Mower should be properly leveled for best mowing performance See "TO LEVEL MOWER HOUSING" in

the Service and Adjustments section of this manual

Use the runner on the right hand side of mower as a guide. The blade cuts approximately an inch outside the runner (See Fig 8).

The !eft hand side of mower should be used for trim- ming

Drive so that clippings are discharged onto the area

that has been cut. Have the cut area to the right of the machine This will result in a more even distribution of

clippings and more uniform cutting

When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig 9)

FIG, 9

If grass is extremely tall, it should be mowed twice to

reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high the second to the des red he ght

Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing

Always operate engine at full throttle when mowing to assure better mowing performance and proper dis- charge of material Regulate ground speed by select- ing a low enough speed to give the mower cutting performance as well as the quality of cut desired

When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Automatic Hydrostatic Lawn Tractor Preparation Maintenance and StorageOperation Product Specifications Maintenance AgreementFull 90 DAY Warranty on Battery Customer ResponsibilitiesIndex Performance EngineContents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Unit from Carton Before Rolling Unit OFF SkidPrepare Battery See Fig HOW to SET UP Your TractorCheck for Proper Position of ALL Belts Check Brake SystemInstall Battery See Figs ChecklistKnow Your Tractor OperatuoTo SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control See FigTo Operate Mower See Fig OperationImportant the Motioncontrollever does Check Engine OIL Level See FigMowing Tips General Recommendations MaintenanceBefore Each USE LubricationTractor Battery See FigBlade Care WellRecommended SAE Viscosity Grades Transaxle Pump Fluid Level See FigsAIR Screen See Fig AIR Filter See FigMuffler Cleaning Servuce and AdjustmentsAINTENANC£ Spark Plugs See FigTo Level Mower Housing Ervice and AdjustmentsOfcurl NUT ETo Adjust Mower Blade Drive Belt Service and AdjustmentsBelt Installation Belt RemovalTo Replace Motion Drive Belt See Figs To Adjust Brake See FigAdjustments ServiceTo Adjust Motion Control Lever See Fig To Adjust Steering Wheel AlignmentTo Remove CABLES, Reverse Order Interlocks and RelaysTo Replace Headlight Bulb To Remove Hood and Grill Assembly Servnce and AdjustmentsFinal Setting To Adjust Throttle Control Cable See FigEngine Governed IdleStorage BatteryOther Fuel SystemTroubleshootbng Pounts Problem Cause CorrectionProblem Cause Correction Troubleshooting PointsSchematic Repaur Parts KEY Part Description @12Standard Hardware - Purchase Locally =.-== Mmommmmommbmml I J J j J J J J J Repair Parts KEY Part 12 HP 38 Riding Lawn Tractor - Model Number DriveKEY Description553O C D KEY Part DescriptionTractor - Model Number 12 HP 38 Riding LawnStandard Hardware - Purchase Locally C D E REPAnR Parts C D E F G H J K L Part KEY Description16x3/4 STD541437 Nut 16UNC Part Description Repair PartsN44 Xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx 4751 EY Part KEY Description =IEPAIR PartsT41 Qil KEY Part NO. no DescriptionKEY Part NO. no Repair PartsLabel KIT GasketsetSlope Sheet 12,0 HP MC Electric Start 38 Mower HOW to Order Repair PartsPRINTE3 in U S

917.25736 specifications

The Craftsman 917.25736 is a standout model in the realm of lawn tractors, offering remarkable performance and versatility for homeowners with medium to large lawns. Engineered to provide an efficient mowing experience, this lawn tractor is perfect for those seeking both power and reliability.

One of the key features of the Craftsman 917.25736 is its robust engine. Equipped with a 19.5 HP Briggs & Stratton engine, this tractor offers ample power to tackle tough mowing tasks. The engine is designed for durability and efficiency, ensuring that users can depend on it for consistent performance season after season.

The cutting deck is another significant highlight of the Craftsman 917.25736. It boasts a 42-inch steel cutting deck that not only provides a wide cutting path but also enhances durability and effectiveness. The adjustable cutting height offers six different positions, allowing users to customize their mowing experience based on their lawn's specific needs.

In terms of technology, the Craftsman 917.25736 features a hydrostatic transmission that delivers smooth and seamless operation. This means users can easily control their speed without the need for manual gear shifting, making it more accessible for individuals of all skill levels. The tight turning radius also allows for better maneuverability around obstacles like trees and flower beds.

The comfort of the operator has not been overlooked in the design of the Craftsman 917.25736. It comes with a plush, high-back seat that provides ample support during long mowing sessions. Additionally, the steering wheel is ergonomically designed, making it easier to handle the tractor over extended periods.

For those concerned about the safety features, this model does not disappoint. The tractor comes with a safety ignition switch that prevents accidental starting, as well as automatic shut-off features that engage when the operator leaves the seat, enhancing its safety profile significantly.

Overall, the Craftsman 917.25736 combines powerful performance, user-friendly technology, and comfort, making it an ideal choice for homeowners looking to maintain their lawns efficiently. With its thoughtful design and reliable features, it stands as a testament to Craftsman’s commitment to quality and innovation in outdoor power equipment. Whether you are mowing a large expanse or navigating tight corners, the Craftsman 917.25736 aims to deliver a dependable and enjoyable mowing experience.
Top Page Image Contents