Craftsman 917.25736 owner manual Tractor, Blade Care, Battery See Fig, Well

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any mainte- nance

TIRES

Maintain proper aJr pressure in all tires (See "PROD- UCT SPECIFICATIONS" on page 3 of this manual)

Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber,

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

BLADE CARE

For best results mower blades must be kept sharp The blades can be sharpened with a file or on a grinding wheel, We suggest they be sharpened or replaced after every 25 hours of mowing Check blades more often if mowing in sandy conditions

Do not attempt to sharpen blades while they are on the mower,

Replace bent or damaged blades

BLADE REMOVAL (See Fig. 10)

Raise mower to highest position to allow access to blades

Remove hex bolt, Iockwasher and flat washer securing blade

Install new or resharpened blade with trailing edge up towards deck as shown

Reassemble hex bolt, Iockwasher and flat washer in exact order as shown

Tighten bolt securely (30-35 Ft Lbs torque)

IMPORTANT: BLADE BOLT IS GRADE 5 HEATTREATED,

(JACKSHAFT) ASSEMBLY

FLANGES

FLAT WASHER

TRAILING

3E

UP

(GRADE5)*

*A GRADE 5 HEAT TREATED BOLT

CAN BE IDENTIFIED BYTHREE LINES ON THE BOLT HEAD AS SHOWN AT LEFT.

FIG. 10

TO SHARPEN BLADE (See Fig. 11)

Care should be taken to keep the blade balance& An unbalanced blade will cause excessive vibration and even-

tual damage to mower and engine

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower,

To check blade balance, drive a nail into abeam orwall.

Leave about one inch of the straight nail exposed, Place center hole of blade over the head of the nail. If

blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced,

CENTER _I I Ij! tJf/, f ..Bt.ADE

HOLE

FIG. 11

BATTERY (See Fig, 12)

Your unit has a battery charging system which is sufficient for normal use, However, periodic charging of the battery with an automotive charger will extend its life,

Acid solution level in each battery cell should be even with bottoms of vent wells, Add only distilled or iron- free water if necessary, Do not overfill.

CUT AWAY VIEW

_

VENTCAP

 

_

._VENT

 

 

WELL

[_

-=_ -=--==_

LEVEL

FIG. 12

Keep battery and terminals clean.

Keep battery bolts tighL

Keep vent caps tight and small vent holes in caps open,

Recharge at 6 amperes for 1 hour,

TO CLEAN BATTERY AND TERMINALS -

Corrosion and dirt on the battery and terminals can cause the battery to "leak" power.

Remove terminal guard,

Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor,

Wash battery with solution of four tablespoons of bak-

ing soda to one gallon of water, Be careful not to get the soda solution into the cells,

Rinse the battery with plain water and dry,

Clean terminals and battery cable ends with wire brush until bright,

Coat terminals with grease or petroleum jelly,

Reinstall battery (See "INSTALL BATTERY" in the Assembly section of this manual).

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Automatic Hydrostatic Lawn Tractor Maintenance and Storage PreparationOperation Customer Responsibilities Maintenance AgreementProduct Specifications Full 90 DAY Warranty on BatteryIndex Performance EngineContents of Hardware Pack Before Rolling Unit OFF Skid AssemblyTools Required for Assembly To Remove Unit from CartonCheck Brake System HOW to SET UP Your TractorPrepare Battery See Fig Check for Proper Position of ALL BeltsInstall Battery See Figs ChecklistKnow Your Tractor OperatuoTo USE Throttle Control See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigCheck Engine OIL Level See Fig OperationTo Operate Mower See Fig Important the Motioncontrollever doesMowing Tips Lubrication MaintenanceGeneral Recommendations Before Each USEWell Battery See FigTractor Blade CareRecommended SAE Viscosity Grades Transaxle Pump Fluid Level See FigsAIR Filter See Fig AIR Screen See FigMuffler Spark Plugs See Fig Servuce and AdjustmentsCleaning AINTENANC£NUT E Ervice and AdjustmentsTo Level Mower Housing OfcurlBelt Removal Service and AdjustmentsTo Adjust Mower Blade Drive Belt Belt InstallationTo Replace Motion Drive Belt See Figs To Adjust Brake See FigTo Adjust Steering Wheel Alignment ServiceAdjustments To Adjust Motion Control Lever See FigInterlocks and Relays To Remove CABLES, Reverse OrderTo Replace Headlight Bulb To Remove Hood and Grill Assembly Servnce and AdjustmentsGoverned Idle To Adjust Throttle Control Cable See FigFinal Setting EngineFuel System BatteryStorage OtherTroubleshootbng Pounts Problem Cause CorrectionProblem Cause Correction Troubleshooting PointsSchematic Repaur Parts @12 KEY Part DescriptionStandard Hardware - Purchase Locally =.-== Mmommmmommbmml I J J j J J J J J Repair Parts Description 12 HP 38 Riding Lawn Tractor - Model Number DriveKEY Part KEY553O C D KEY Part DescriptionTractor - Model Number 12 HP 38 Riding LawnStandard Hardware - Purchase Locally C D E REPAnR Parts C D E F G H J K L Part KEY Description16x3/4 STD541437 Nut 16UNC Part Description Repair PartsN44 Xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx 4751 EY Part KEY Description =IEPAIR PartsT41 Qil KEY Part NO. no DescriptionGasketset Repair PartsKEY Part NO. no Label KITSlope Sheet HOW to Order Repair Parts 12,0 HP MC Electric Start 38 MowerPRINTE3 in U S

917.25736 specifications

The Craftsman 917.25736 is a standout model in the realm of lawn tractors, offering remarkable performance and versatility for homeowners with medium to large lawns. Engineered to provide an efficient mowing experience, this lawn tractor is perfect for those seeking both power and reliability.

One of the key features of the Craftsman 917.25736 is its robust engine. Equipped with a 19.5 HP Briggs & Stratton engine, this tractor offers ample power to tackle tough mowing tasks. The engine is designed for durability and efficiency, ensuring that users can depend on it for consistent performance season after season.

The cutting deck is another significant highlight of the Craftsman 917.25736. It boasts a 42-inch steel cutting deck that not only provides a wide cutting path but also enhances durability and effectiveness. The adjustable cutting height offers six different positions, allowing users to customize their mowing experience based on their lawn's specific needs.

In terms of technology, the Craftsman 917.25736 features a hydrostatic transmission that delivers smooth and seamless operation. This means users can easily control their speed without the need for manual gear shifting, making it more accessible for individuals of all skill levels. The tight turning radius also allows for better maneuverability around obstacles like trees and flower beds.

The comfort of the operator has not been overlooked in the design of the Craftsman 917.25736. It comes with a plush, high-back seat that provides ample support during long mowing sessions. Additionally, the steering wheel is ergonomically designed, making it easier to handle the tractor over extended periods.

For those concerned about the safety features, this model does not disappoint. The tractor comes with a safety ignition switch that prevents accidental starting, as well as automatic shut-off features that engage when the operator leaves the seat, enhancing its safety profile significantly.

Overall, the Craftsman 917.25736 combines powerful performance, user-friendly technology, and comfort, making it an ideal choice for homeowners looking to maintain their lawns efficiently. With its thoughtful design and reliable features, it stands as a testament to Craftsman’s commitment to quality and innovation in outdoor power equipment. Whether you are mowing a large expanse or navigating tight corners, the Craftsman 917.25736 aims to deliver a dependable and enjoyable mowing experience.
Top Page Image Contents