Craftsman 358.792441 manual Scalping, Mowing, What Causes Blade Thrust, When Blade Thrust Occurs

Page 12

*The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences.

*For trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially:

•During light duty cutting.

•Near objects around which the line can wrap such as small posts, trees or fence wire.

*For mowing or sweeping, use full

throttle for a good clean job. TRIMMING - Hold the bottom of the

trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Trimming

SCALPING - The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Al- low the tip of the line to strike the ground around trees, posts, monu- ments, etc. This technique increases line wear.

Scalping

MOWING - Your trimmer is ideal for

mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

Mowing

SWEEPING - The fanning action of the rotating line can be used to blow away loose debris from an area. Keep the line parallel to and above the area surface and swing the tool from side to side.

/._Sweeping

_'8 r

OPERATING INSTRUCTIONS FOR

USE OF BRUSHCUTTER ATTACH* MENT WITH WEED BLADE

*Blade Thrust is a reaction that only occurs when using a bladed unit. This reaction can cause serious injury such as amputation. Carefully study this section. It is important that you under- stand what causes blade thrust, how you can reduce the chance of its oc-

curring, and how you can remain in control of unit if blade thrust occurs.

*WHAT CAUSES BLADE THRUST -

Blade Thrust can occur when spin- ning blade contacts an object that it does not cut. This contact causes blade to stop for an instant and then

suddenly move or "thrust" away from object that was hit. The "thrusting" re- action can be violent enough to cause operator to be propelled in any direc- tion and lose control of unit. The un- controlled unit can cause serious injury if blade contacts operator or others.

*WHEN BLADE THRUST OCCURS

-Blade Thrust can occur without

warning if the blade snags, stalls, or

binds. This is more likely to occur in areas where it is difficult to see the

material being cut. By using the unit properly, the occurrence of blade thrust will be reduced and the opera- tor will be less likely to lose control.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Brushcutter Attachment Full ONE Year Warranty on Craftsman Brushcutter Attachment Sears, Roebuck and Co., I/817 WA, Hoffman Estates, ILOperator Safety Always WearUNIT/MAINTENANCE Safety Fuel SafetyCutting Safety Transporting and StorageCarton Contents Installing Brushcutter AT- TachmentHandlebar Assembly Shoulder Strap Assembly Lower Shoulder Strap ClampConfiguring Your Unit Assembly Information Trimmer HeadInstallation of the Trimmer HeadAssembly Information Weed Blade Attaching the Plastic ShieldAttaching the Metal Shield Installation of the Metal Blade Ightenevenlyandsecurelywith thehexwrenchprovidedTrimmer Head Operating the CouplerTrimmer Shield Installingoptional Attach Ment Tube ReleaseUSE of Brushcutter ATTACH* Ment with Trimmer Head When Blade Thrust Occurs ScalpingMowing What Causes Blade ThrustRecommended Cutting Position Maintenance Schedule Care and Maintenance TaskBlade Maintenance Line ReplacementBlade Replacement Seasonal StorageReplacing the Cutting Head Sears MAS Cercano EN LOS Estados Unidos Sears, Roebuck and Co., 13/817 WA Hoffman Estates, ILDadvertencia AdvertenciaUtilice Siem ADVERTENClA Zona de peligroSeguridad CON EL Combus TibleMantenimiento Seguridad DEL AparatoTransporte Y Almacenamiento Contenido DE LA CajaMontaje Installation DEL Mango Peligro Riesgo DE Corta Instalacionde LA AccesorioDEL Cortadora DE Malezas Precaucion AI instalar las acceso Base DE AbrazaderaMontaje DE LA Correa Para Abrazadera Inferior DEL Correa Para HombroHombro EXTREM0 CON EL Cabeza DE MotorCONFIGURACI3N DEL Aparato INFORMACI3N DE Montaje Cabezal DE CortePara Instalar EL Cabezal DE Corte Manualmente INFORMACI3N DE Montaje Cuchillas Papa MalezasPara Instalar EL Protector Plastica Para Nstalar EL Cabezal DE CorteMON.TAJE DE LA Cuchilla Metamca Conozca SU Cortadora DE Malezas Accesorio OPERAClON DEL AcopladorProtector DE LA Cuchilla Como Remover EL Accesorio DEL Cortadora DE Malezas UINSTALACI6NDEL Accesorios Instacalin DEL SuspensorCabezal DE Corte Metodos DE CorteLa punta de la linea La linea est metida Dentro del materialCorrectaIncorrecta Para BarterCausas DEL Rebote DE LA Cuchilla El Rebote de la Cronograma DE Mantenimiento Tarea DE Cuidado Y MantenimientoMantenimiento DE LA Cuchilla La cuchilla siReemplazo DE LA Linea EN EL Cabezal DE Corte DE Lnea Fija Use siempre inea de recambio CraftsmanReemplazo DE LA Cabezal DE Corte Cambio DE LA Cuchilla4ADVERTENCIA Realice los si

358.792441 specifications

The Craftsman 358.792441 is a versatile and powerful tool designed for outdoor use, particularly renowned for its performance in lawn care and garden maintenance. This string trimmer positions itself as an essential companion for homeowners and landscaping professionals alike, allowing for efficient trimming of grass and weeds in hard-to-reach areas.

One of the standout features of the Craftsman 358.792441 is its robust 29cc gas-powered engine. This engine delivers ample power, enabling the trimmer to handle tough vegetation with ease. The 2-cycle engine design not only provides reliable performance but also ensures that the tool remains lightweight and easy to maneuver, crucial for long trimming sessions.

The Craftsman 358.792441 is equipped with an automatic line-feed system. This technology allows for a hassle-free experience, automatically feeding the cutting line as needed, reducing downtime for manual adjustments. The dual-line cutting system enhances operational efficiency, allowing for a wider cutting path that speeds up the trimming process.

Another significant characteristic of this trimmer is its adjustable straight shaft design. This feature allows users to customize the length of the tool for maximum comfort, ensuring that it can be used effectively by individuals of varying heights. The straight shaft also provides better reach into tight spaces and under bushes, making it a practical choice for thorough landscaping tasks.

The Craftsman 358.792441 also showcases a user-friendly starting system. The Easy Start technology minimizes pull resistance, making it easier to start the engine, which is particularly beneficial for users who are not accustomed to operating gas-powered tools. Additionally, its comfortable, ergonomic handle design reduces user fatigue during extended use, allowing for greater control and precision.

In terms of durability, the construction of the Craftsman 358.792441 is designed to withstand the rigors of frequent outdoor use. With a sturdy build and quality components, this trimmer offers longevity and reliability that users can depend on season after season.

Overall, the Craftsman 358.792441 combines power, efficiency, and user-friendly features, making it an excellent choice for anyone looking to maintain their lawn or garden. Whether you are a homeowner or a professional landscaper, this trimmer provides the performance and ease of use needed to tackle a variety of outdoor tasks effectively.
Top Page Image Contents