Craftsman 917.258911 Service and ADJ, Engine, To Replace Headlight Bulb, Interlocks and Relays

Page 26

SERVICE AND ADJ

TO REPLACE HEADLIGHT BULB

•Raise hood,

•Puff bulb holder out of the hole in the backside of the gritL

°Replace bulb in holder'and push bulb holder securely back into the hole in the backside of the griH_

°Close hood.

°Raise hood°

•Unsnap headlight wire connector.

°Stand in front of tractor° Grasp hood at sides, tiff toward engine and lift off of tractor.

°To replace, reverse above procedures.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring° See electrical wiring diagram in the Repair Parts section of this manual.

TO REPLACE FUSE

Replace with 30 amp automotive-typeplug-in fuse. The fuse holder is located behind the dash,

/_

i;%,,

HEADLIGHT

 

• : s

 

 

 

 

WIRE

 

 

CONNECTOR

HOOD

TO ADJUST ATTACHMENT LIFT SPRING (See Fig, 32)

•While holding spring bushing with wrench, loosen jam nut..

•Turn adjustment bolt clockwise to extend spring and reduce lift effort for heavier attachments°

. Turn adjustment bolt counterclockwise for'lighter'at- tachments.

°Retighten jam nut against spring bushing.

IMPORTANT, DO NOT ADJUST FOR MAXIMUM SPR{NG

TENSION WHEN USING LIGHT ATTACHMENTS SUCH AS A MOWER, ADJUST LIFT LEVER SPRING TO AID IN LIFTING ATTACHMENT. DO NOT OVERPOWER SPRING.

WHEN REMOVING ATTACHMENT, ALWAYS ADJUST SPRING TENSION TO ITS LOWEST POSITION_

TO REMOVE HOOD AND GRILL ASSEMBLY See Fig, 33)

ADJUSTMENT

SPRING BUSHING

o ATTACHMENT

JAM NUT LIFT SPRING

o _

FIG. 32

FIG. 33

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig, 34)

The throttle control has been preset at the factory and

adjustment should not be necessar¥_ Check adiustment as described below before loosening cable° If adjustment is

necessary',proceed as follows:

°With engine not running, move throttle control lever to fast position.

°Check that speed contro! lever is against stop screw. If it is not, loosen casing clamp screw and pull throttle cable until lever is against screw_ Tighten clamp screw securely_

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents For Consumer Assistance HOT LINE, Call this Toll Free Numbei III. Children Safe Operation Practices for Ride-On MowersIL Slope Operation Customer Responsibilities Maintenance AgreementLimited 90 DAY Warranty on Battery ModelAssembly Product SpecificationsTractor Accessories Parts ORDERING/SERVICE Back CoverEngine Maintenance PerformanceHardware Pack Parts Bag contents shownParts bag contents not shown full siz e To Remove Tractor from Carton Tools Required for AssemblyHOW to SET UP Your Tractor Before Rolling Tractor OffskidCheck Tire Pressure Install Seat See FigWHEEL/I Check Brake SystemSee Figs Install Mower and Drive BeltMbly Check Mower LevelnessChecklist BLYBattery Reverse Forward Fast Slow LockOperati Know Your TractorTo SET Parking Brake See Fig HOW to USE Your TractorTo Adjust Mower Cutting Height See Fig Stopping See FigTo Operate on Hills To Adjust Gauge Wheels See Fig, 8ATo Operate Mower See Figs To Transport See FigsHydrostatic Transmission Warm UP Before Starting the EngineADD Gasoline Ning Mowing TipsPurge Transmission Before Operating the TractorGeneral Recommendations Maintenance ScheduleLubrication Chart Before Each USEBrake Operation BatteryTractor TiresTransaxle Pump Fluid BeltsLubrication Customer RES Ponsibilities CleaningClean AIR INTAKE/COOLING Areas Engine OIL FilterTo Remove Mower See Fig To Level Mower HousingTo Install Mower Important if AN Attachment Other thanPosition Service and Adjust EntsTo Replace Mower Drive Belt Mower Drive Belt Removal See FigSee Fig To Adjust Attachment ClutchTo Adjust Brake See Fig To Replace Mower Blade Drive BeltTransmission REMOVAL/REPLACEMENT Service and AdjuTo Adjust Motion Control Lever See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Rvice and AdjustmentsFront Wheel TOE-IN Adjustment To Remove Wheel for RepairsTo Replace Headlight Bulb Service and ADJEngine Interlocks and RelaysFinal Setting To Adjust Choke Control See FigsTo Adjust Carburetor See Fig AdjustmentsEngine OIL StorageFuel System Problem Cause Correction Troubleshooti PointsPoints Problem CauseTroubleshooti Engine Connector Tractor Tractor - Model NumberTractor - Model Number ElectricalRepair Parts KEY Part DescriptionChassis and Enclosures 47120 1815 64 17Unc x O0L NUMe 9772S89!1 KEY Part Ground DriveBearing, Idler NO. NO. DescriptionSteering Assembly Steering Assembly Engine 37 tEngine See Breakdown Seat Assembly 715 Wheels & TiresDecals KEY Part3834 Lift Assembly2O 19 Indicator Mower Deck NO. no 7398Q500Repair Parts Description Tractor - Model Number Hydro Gear Transaxle - Model NumberKEY Part NO. no Descripon 122699X Hydro Gear Pump Model Number BU-10L-122KEY Part Description NO. no 122767XKohler Engine Model Number CV22S, Type Number T1!ljKEY Part NO. no Kohler ENGINE- Model Number CV22S, Type NumberCylinder HEAD/VALVE/BREATHER Crankcase KEY Part OwE,,Ous,,,o. BF i....................., s 20 19 18 17Not Illustrated TRACTOR- Model NumberNot Illustrated AIR IntakeSARTINGs,! ...........EM 19 1815 ,oFilter,Oil Starting System Engine Controls KEY Part NO. no DescriponOIL PAN/LUBRICATION KEY Part Description Tractor -- Model Number Notillustrated KEY Part NO. no Description Not Illustrated CrankshaftExhaust KEY Part NO. no Description 24-75503 GasketSetLI.I Owners AL If YOU Need Repair Service or PartsFor Repair SERVICE, Call this Toll Free Number MODEl, Number ,,917,258911

917.258911 specifications

The Craftsman 917.258911 is a formidable lawn tractor designed to provide exceptional performance and versatility for homeowners and landscape enthusiasts. This model stands out due to its combination of power, efficiency, and comfort, making it an ideal choice for maintaining larger lawns and complex landscapes.

One of the key features of the Craftsman 917.258911 is its powerful engine. Equipped with a robust 24 HP Briggs & Stratton engine, it delivers reliable power that enables the tractor to tackle tough mowing jobs with ease. The engine is designed with overhead valve technology, which enhances fuel efficiency and improves overall performance. It starts quickly and is engineered for durability, ensuring that users can depend on it season after season.

The cutting deck on the Craftsman 917.258911 is another highlight, featuring a generous 54-inch design that allows for wide, efficient mowing in fewer passes. The deck is fabricated from a durable welded steel, providing strength and longevity while helping to deliver clean cuts. The deck also features a deck washout port, enabling easy cleaning to maintain optimal performance and longevity.

This lawn tractor offers a six-position height adjustment lever, allowing users to customize grass cutting heights according to their preferences or grass type. This level of adjustability ensures that the mower can tackle various mowing conditions effectively.

For added comfort, the Craftsman 917.258911 is designed with a spacious, high-back seat that provides support during extended mowing sessions. The seat is adjustable, accommodating various operator heights and ensuring an ergonomic driving experience. The inclusion of oversized, smooth-rolling tires enhances maneuverability and stability, making it easier to navigate uneven terrain.

Technology plays a role in the Craftsman 917.258911, as it is equipped with a hydrostatic transmission that offers seamless speed adjustments without the need for shifting gears. This feature enhances the ease of operation, allowing users to focus on their mowing tasks without distractions.

Other notable characteristics include its rugged construction, easy steering, and front-mounted headlights for improved visibility during early morning or late evening mowing sessions. Overall, the Craftsman 917.258911 combines power, comfort, and advanced technology, making it an excellent investment for anyone looking to maintain a beautiful lawn with efficiency and ease.
Top Page Image Contents