Craftsman 917.258911 owner manual Service and Adju, To Adjust Motion Control Lever See Fig

Page 24

SERVICE AND ADJU

i =l= i=l=l=Hl=l.......................................

TO REPLACE MOTION DRIVE BELT

(See Fig. 26)

Park the tractor on level surface,. Engage parking brake_ For ease of service there is a belt installationguide decal on bottom of left footrest.

oRemove mower (See 'q'OREMOVE MOWER" in this section of this manual.)

BELT REMOVAL

=Engage parking brake (creates slack in belt)_

Remove bert from clutching and fan idler pulleys..

°Loosen belt keeper above transaxle pulley.

°Remove belt from transaxie pulley_

°Remove belt from engine pulley and front V-idler pul- ley.,

°Pull belt out of all belt keepers and remove from tractor°

BELT INSTALLATION -

Place V part of belt into grooves on engine pulley and front V-idler, making sure to route belt inside of all belt keepers.,

Route belt on right side, coming from V-idler, towards back of tractor, above midspan belt keeper'and to top of transaxle pulley.

°Route belt on left side, coming from engine pulley, towards back of tractor and through loop in mldspan belt keeper.

=Place V part of belt into grooves on transaxle and fan idterpulleys, making sure to route belt insideof all belt keepers°

°Retighten belt keeper above transaxle pulley.

Place belt around clutching idlers as shown, making sure to route belt inside of all belt keepers.,

-Check to be sure belt is positioned correctly and is on proper side of art belt keepers.

o Reinstall mower,.

IMPORTANT; CHECK BRAKE ADJUSTMENT.

TRACTOR V-BELTDRIVE SCHEMATIC

VIEWED FROM L.H. SIDE OF TRACTOR

CLUTCHINGTRANSAXLE

BELT PULLEY

KEEPER

ENGINE

PULLEY

V-IDLER KEEPER

TO ADJUST MOTION CONTROL LEVER (See Fig. 27)

The motion control lever has been preset at the factory and adjustment should not be necessary_

If for any reason the motion control lever will not hold its positionwhile at a selected speed, itmay be adjusted at the friction pack located on the right side of chassis,

Park tractor on level surfacer Stop tractor by turning

ignition key to "OFF" position and engage parking brake_

=Place motion control lever in neutral (N) position_ o While holding locknut, toosen jam nut

°Tighten tocknut 1/4 turn,

White holding Iocknut, tighten jam nut securely_

NOTE: if for any reason the effort to move the motion control lever becomes too excessive, reverse the above

adjustment procedure by loosening iocknut 1/4 turn_

Road test tractor after adjustment and repeat procedure if necessary_

LOCKNUT

, JAM NUT

FIG. 27

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, itshould be purged after reinstallation before operating the tractor. See "PURGE TRANSMiSSiON" in Operation section of this manual,

KEEPERBELT

TWISTS

BELTFAN

KEEPER IDLER

AS VIEWED FROM BOTTOM

TO ADJUST STEERING WHEEL ALIGNMENT

if steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ir_,gwheel and reassemble per instructions in the Assembly section of this manual

FIG. 26

24

Image 24
Contents For Consumer Assistance HOT LINE, Call this Toll Free Numbei Safe Operation Practices for Ride-On Mowers IL Slope OperationIII. Children Maintenance Agreement Limited 90 DAY Warranty on BatteryCustomer Responsibilities ModelProduct Specifications Tractor AccessoriesAssembly Parts ORDERING/SERVICE Back CoverEngine Maintenance PerformanceParts Bag contents shown Parts bag contents not shown full siz eHardware Pack Tools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Before Rolling Tractor OffskidInstall Seat See Fig WHEEL/ICheck Tire Pressure Check Brake SystemInstall Mower and Drive Belt MblySee Figs Check Mower LevelnessChecklist BLYBattery Reverse Forward Fast Slow LockOperati Know Your TractorHOW to USE Your Tractor To Adjust Mower Cutting Height See FigTo SET Parking Brake See Fig Stopping See FigTo Adjust Gauge Wheels See Fig, 8A To Operate Mower See FigsTo Operate on Hills To Transport See FigsBefore Starting the Engine ADD GasolineHydrostatic Transmission Warm UP Mowing Tips Purge TransmissionNing Before Operating the TractorMaintenance Schedule Lubrication ChartGeneral Recommendations Before Each USEBattery TractorBrake Operation TiresBelts LubricationTransaxle Pump Fluid Cleaning Clean AIR INTAKE/COOLING AreasCustomer RES Ponsibilities Engine OIL FilterTo Level Mower Housing To Install MowerTo Remove Mower See Fig Important if AN Attachment Other thanService and Adjust Ents To Replace Mower Drive BeltPosition Mower Drive Belt Removal See FigTo Adjust Attachment Clutch To Adjust Brake See FigSee Fig To Replace Mower Blade Drive BeltService and Adju To Adjust Motion Control Lever See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentRvice and Adjustments Front Wheel TOE-IN AdjustmentTo Start Engine with a Weak Battery See Fig To Remove Wheel for RepairsService and ADJ EngineTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Choke Control See Figs To Adjust Carburetor See FigFinal Setting AdjustmentsStorage Fuel SystemEngine OIL Problem Cause Correction Troubleshooti PointsProblem Cause TroubleshootiPoints Engine Connector Tractor Tractor - Model NumberTractor - Model Number ElectricalRepair Parts KEY Part DescriptionChassis and Enclosures 47120 1815 64 17Unc x O0L NUMe 9772S89!1 Ground Drive Bearing, IdlerKEY Part NO. NO. DescriptionSteering Assembly Steering Assembly Engine 37 tEngine See Breakdown Seat Assembly Wheels & Tires Decals715 KEY PartLift Assembly 2O 193834 Indicator Mower Deck NO. no 7398Q500Repair Parts Tractor - Model Number Hydro Gear Transaxle - Model Number KEY Part NO. no DescriponDescription Hydro Gear Pump Model Number BU-10L-122 KEY Part Description NO. no122699X 122767XKohler Engine Model Number CV22S, Type Number T1!ljKohler ENGINE- Model Number CV22S, Type Number Cylinder HEAD/VALVE/BREATHER Crankcase KEY PartKEY Part NO. no OwE,,Ous,,,o. BF i....................., s 20 19 18 17TRACTOR- Model Number Not IllustratedNot Illustrated AIR IntakeSARTINGs,! ...........EM 19 1815 ,oStarting System Engine Controls KEY Part NO. no Descripon OIL PAN/LUBRICATION KEY Part DescriptionFilter,Oil Tractor -- Model Number Not Illustrated Crankshaft Exhaust KEY Part NO. no DescriptionNotillustrated KEY Part NO. no Description 24-75503 GasketSetLI.I If YOU Need Repair Service or Parts For Repair SERVICE, Call this Toll Free NumberOwners AL MODEl, Number ,,917,258911

917.258911 specifications

The Craftsman 917.258911 is a formidable lawn tractor designed to provide exceptional performance and versatility for homeowners and landscape enthusiasts. This model stands out due to its combination of power, efficiency, and comfort, making it an ideal choice for maintaining larger lawns and complex landscapes.

One of the key features of the Craftsman 917.258911 is its powerful engine. Equipped with a robust 24 HP Briggs & Stratton engine, it delivers reliable power that enables the tractor to tackle tough mowing jobs with ease. The engine is designed with overhead valve technology, which enhances fuel efficiency and improves overall performance. It starts quickly and is engineered for durability, ensuring that users can depend on it season after season.

The cutting deck on the Craftsman 917.258911 is another highlight, featuring a generous 54-inch design that allows for wide, efficient mowing in fewer passes. The deck is fabricated from a durable welded steel, providing strength and longevity while helping to deliver clean cuts. The deck also features a deck washout port, enabling easy cleaning to maintain optimal performance and longevity.

This lawn tractor offers a six-position height adjustment lever, allowing users to customize grass cutting heights according to their preferences or grass type. This level of adjustability ensures that the mower can tackle various mowing conditions effectively.

For added comfort, the Craftsman 917.258911 is designed with a spacious, high-back seat that provides support during extended mowing sessions. The seat is adjustable, accommodating various operator heights and ensuring an ergonomic driving experience. The inclusion of oversized, smooth-rolling tires enhances maneuverability and stability, making it easier to navigate uneven terrain.

Technology plays a role in the Craftsman 917.258911, as it is equipped with a hydrostatic transmission that offers seamless speed adjustments without the need for shifting gears. This feature enhances the ease of operation, allowing users to focus on their mowing tasks without distractions.

Other notable characteristics include its rugged construction, easy steering, and front-mounted headlights for improved visibility during early morning or late evening mowing sessions. Overall, the Craftsman 917.258911 combines power, comfort, and advanced technology, making it an excellent investment for anyone looking to maintain a beautiful lawn with efficiency and ease.