Craftsman 917.258911 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 7

LY

Your new tractor has been assembled at the factorywith the exception of those parts left unassembled fo rshipping purposes.. To ensure safe and proper operation of your tractor al! parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.,

TOOLS REQUIRED FOR ASSEMBLY

STEERING WHEEL INSERT

A socket wrench set will make assembly easier,. Standard wrench sizes are listed..

(2)

7/16" wrenches

Tire pressure gauge

(1)

1/2" wrench

Utility knife

(1)

9/16" wrench

 

(1)

3/4" socket with drive ratchet

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel)°

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton (See page 6),,

•Cut, from top to bottom, along lines on alt four corners of carton, and lay panels flat.

,o Check for any additional loose parts or cartons and remove°

BEFORE ROLLING TRACTOR OFFSKID

ATTACH STEERING WHEEL (See Fig. 1)

•Remove hex bolt, lock washer and large fiat washer from steering shaft..

•Position front wheels of the tractor so they are pointing straight forward.

°Slide steering sleeve over steering shaft,.

°Position steering wheel so cross bars are horizontal (left to right) and slide onto steering wheel adapter.

. Secure steering wheel to steering shaft with hex bolt, lock washer and large flat washer previously removed., Tighten securely.

•Snap steering wheel insert into center of steering wheel.

oRemove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES

IN SKIDTHAT MAY PUNCTURETIRES WHERE TRACTOR IS TO ROLL OFF SKID.

TO ROLLTRACTOR OFF SKID (See Operation section for location and function of controls)

°Press lift lever plunger and raise attachment lift lever to its highest positiono

°Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in freewheeling position to disengage transmission (See 'TO TRANSPORT" in the Operation section of this manual)..

•Roll tractor forward off skid.

°Remove mower and packing materials..

° Remove ties from V-belts,

7

STEERING

 

_,_,_

STEERING

WHEEL

_

_LLIL)_ /

SHAFT

ADAPTER

 

 

 

I/.#

I

_

_ t _" /

i i" "

STEERING/

I

 

t / /

/

SLEEVE /

" _

_

!/-

l /

FIG. 1

HOW TO SET UP YOUR TRACTOR

CONNECT BATTERY (See Fig. 2)

•Lift hood to raised position°

•Open terminal access doors, remove terminal protec- tive caps and discard.

°If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps.

•First connect RED battery cable to positive (+) battery terminal with hex bolt, flat washer, lock washer and hex nut as shown, Tighten securely,

•Connect BLACK grounding cable to negative (-) bat- tery terminal with remaining hex bolt, fiat washer, lock washer and hex nut. Tighten securely.

•Close terminal access doors.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents For Consumer Assistance HOT LINE, Call this Toll Free Numbei IL Slope Operation Safe Operation Practices for Ride-On MowersIII. Children Model Maintenance AgreementLimited 90 DAY Warranty on Battery Customer ResponsibilitiesParts ORDERING/SERVICE Back Cover Product SpecificationsTractor Accessories AssemblyPerformance Engine MaintenanceParts bag contents not shown full siz e Parts Bag contents shownHardware Pack Before Rolling Tractor Offskid Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonCheck Brake System Install Seat See FigWHEEL/I Check Tire PressureCheck Mower Levelness Install Mower and Drive BeltMbly See FigsBLY ChecklistLock Battery Reverse Forward Fast SlowKnow Your Tractor OperatiStopping See Fig HOW to USE Your TractorTo Adjust Mower Cutting Height See Fig To SET Parking Brake See FigTo Transport See Figs To Adjust Gauge Wheels See Fig, 8ATo Operate Mower See Figs To Operate on HillsADD Gasoline Before Starting the EngineHydrostatic Transmission Warm UP Before Operating the Tractor Mowing TipsPurge Transmission NingBefore Each USE Maintenance ScheduleLubrication Chart General RecommendationsTires BatteryTractor Brake OperationLubrication BeltsTransaxle Pump Fluid Engine OIL Filter CleaningClean AIR INTAKE/COOLING Areas Customer RES PonsibilitiesImportant if AN Attachment Other than To Level Mower HousingTo Install Mower To Remove Mower See FigMower Drive Belt Removal See Fig Service and Adjust EntsTo Replace Mower Drive Belt PositionTo Replace Mower Blade Drive Belt To Adjust Attachment ClutchTo Adjust Brake See Fig See FigTo Adjust Steering Wheel Alignment Service and AdjuTo Adjust Motion Control Lever See Fig Transmission REMOVAL/REPLACEMENTTo Remove Wheel for Repairs Rvice and AdjustmentsFront Wheel TOE-IN Adjustment To Start Engine with a Weak Battery See FigInterlocks and Relays Service and ADJEngine To Replace Headlight BulbAdjustments To Adjust Choke Control See FigsTo Adjust Carburetor See Fig Final SettingFuel System StorageEngine OIL Troubleshooti Points Problem Cause CorrectionTroubleshooti Problem CausePoints Tractor - Model Number Engine Connector TractorElectrical Tractor - Model NumberKEY Part Description Repair Parts47120 1815 64 17 Chassis and EnclosuresUnc x O0L NUMe 9772S89!1 NO. NO. Description Ground DriveBearing, Idler KEY PartSteering Assembly Steering Assembly 37 t EngineEngine See Breakdown Seat Assembly KEY Part Wheels & TiresDecals 7152O 19 Lift Assembly3834 Indicator Mower Deck 7398Q500 NO. noRepair Parts KEY Part NO. no Descripon Tractor - Model Number Hydro Gear Transaxle - Model NumberDescription 122767X Hydro Gear Pump Model Number BU-10L-122KEY Part Description NO. no 122699XT1!lj Kohler Engine Model Number CV22S, Type NumberCylinder HEAD/VALVE/BREATHER Crankcase KEY Part Kohler ENGINE- Model Number CV22S, Type NumberKEY Part NO. no 20 19 18 17 OwE,,Ous,,,o. BF i....................., sAIR Intake TRACTOR- Model NumberNot Illustrated Not Illustrated19 1815 ,o SARTINGs,! ...........EMOIL PAN/LUBRICATION KEY Part Description Starting System Engine Controls KEY Part NO. no DescriponFilter,Oil Tractor -- Model Number 24-75503 GasketSet Not Illustrated CrankshaftExhaust KEY Part NO. no Description Notillustrated KEY Part NO. no DescriptionLI.I MODEl, Number ,,917,258911 If YOU Need Repair Service or PartsFor Repair SERVICE, Call this Toll Free Number Owners AL

917.258911 specifications

The Craftsman 917.258911 is a formidable lawn tractor designed to provide exceptional performance and versatility for homeowners and landscape enthusiasts. This model stands out due to its combination of power, efficiency, and comfort, making it an ideal choice for maintaining larger lawns and complex landscapes.

One of the key features of the Craftsman 917.258911 is its powerful engine. Equipped with a robust 24 HP Briggs & Stratton engine, it delivers reliable power that enables the tractor to tackle tough mowing jobs with ease. The engine is designed with overhead valve technology, which enhances fuel efficiency and improves overall performance. It starts quickly and is engineered for durability, ensuring that users can depend on it season after season.

The cutting deck on the Craftsman 917.258911 is another highlight, featuring a generous 54-inch design that allows for wide, efficient mowing in fewer passes. The deck is fabricated from a durable welded steel, providing strength and longevity while helping to deliver clean cuts. The deck also features a deck washout port, enabling easy cleaning to maintain optimal performance and longevity.

This lawn tractor offers a six-position height adjustment lever, allowing users to customize grass cutting heights according to their preferences or grass type. This level of adjustability ensures that the mower can tackle various mowing conditions effectively.

For added comfort, the Craftsman 917.258911 is designed with a spacious, high-back seat that provides support during extended mowing sessions. The seat is adjustable, accommodating various operator heights and ensuring an ergonomic driving experience. The inclusion of oversized, smooth-rolling tires enhances maneuverability and stability, making it easier to navigate uneven terrain.

Technology plays a role in the Craftsman 917.258911, as it is equipped with a hydrostatic transmission that offers seamless speed adjustments without the need for shifting gears. This feature enhances the ease of operation, allowing users to focus on their mowing tasks without distractions.

Other notable characteristics include its rugged construction, easy steering, and front-mounted headlights for improved visibility during early morning or late evening mowing sessions. Overall, the Craftsman 917.258911 combines power, comfort, and advanced technology, making it an excellent investment for anyone looking to maintain a beautiful lawn with efficiency and ease.
Top Page Image Contents