Craftsman 486.24839 owner manual Become alert!! Your safety is involved

Page 3

Any power equipment can cause injury if operated improperly or if the user does not understand hew to operate the equipment. Exercise caution at all times, when using power equipment.

Read this owner's manual carefully and know how to operate your snow thrower and how to stop the unit and disengage the controls quickly.

Never allow children to operate the equipment.

Never allow adults to operate the equipment without proper instruction.

Keep the area of operation clear of all persons, especially small children, and pets.

Thoroughly inspect the area where the equipment is to be used and remove all door mats, sleds, boards, wires and other foreign objects.

Disengage all clutches and shift into neutral before starting engine.

Do not operate equipment without wearing ad- equate winter outer garments.

Wear substantial footwear which will protect feet and improve footing on slippery surfaces.

Check fuel before starting the engine. Do not remove the fuel cap or fill the fuel tank while the engine is running or hot. Do not fill the fuel tank indoors. Gasoline is an extremely flammable fuel.

Make sure the snow thrower height is adjusted to clear the type surface it will be used on.

Do not use the snow thrower without the rear weight attached to the tractor.

Never make any adjustments while the engine is running.

Always wear safety glasses or eye shield during operation or while performing and adjustment or repair.

Do not place hand or feet near rotating parts. Keep clear of the discharge opening at all times.

Use extreme caution when operating on or crossing gravel surfaces.

Do not carry passengers.

After striking a foreign object, stop the engine, remove the wire from the spark plug and then thoroughly inspect the snow thrower for damage.

Repair any damage before restarting and operating the snow thrower.

If the snow thrower starts to vibrate abnormally, stop the engine immediately and check for the cause. Vibration is generally a warning of trouble.

Look for this symbol to point out important

Become alert!! Your safety is involved.

Stop the engine whenever you leave the operating position, before unclogging the snow thrower or making any adjustments or inspections.

Take all possible precautions when leaving the unit unattended. Disengage the attachment clutch lever or switch, lower the snow thrower, shift into neutral, set the parking brake, stop the engine and remove the key.

When cleaning, repairing or inspecting, make certain all moving parts have stopped. Disconnect the spark plug wire and keep it away from the plug to prevent accidental starting.

Do not run engine indoors except when transport- ing the snow thrower in or out of the building. Open the outside doors. Exhaust fumes are dangerous. Do not clear snow across the face of slopes. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes. Refer to the slope guide on page 27 of this manual. Never operate the snow thrower without guards, plates or other safety protection devices in place. Never operate the snow thrower near glass enclo- sures, automobiles, window wells, drop offs etc. without proper adjustment of the snow thrower discharge angle.

Never direct discharge at bystanders or allow anyone in front of the snow thrower.

Never run the snow thrower into material at high speeds.

Do not overload the machine capacity by attempt- ing to clear snow at too fast a rate.

Never operate the machine at high transport speed on slippery surfaces. Look behind and use care when backing.

Watch for traffic and stay alert when crossing or operating near roadways.

Disengage power to the snow thrower when trans- porting or when not in use.

Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counter weights, cabs etc.)

Never operate the snow thrower without good visibility or light.

 

I

safety precautions. It mean--Attention!!

I

 

h

Image 3
Contents Craftsman Wheel Weight Tire ChainsDrift Cutter Bars Become alert!! Your safety is involved REF. QTY Description Shown Actual SizeNot Shown Actual Size Spare Parts BAGCarton Contents Items Removed from Tractor Assembly of Side Plates to TractorTools Required for Assembly Removal of Parts from CartonRight Side View WasherInstalling Shoulder Bolts ROD Operated Attachment Clutches Installing CLUTCH/IDLER AssemblyTractors Clutch Cable Engine PulleyCable Operated AnACHMENT Clutches Hair Cotter PIN4PULLEY Hairpin Cotier Pivot Lock PINEngine Keeper EngineView of Bottom Electric AnACHMENT ClutchesTensioning Chain Chain SideAssembly of the Snow Thrower Crank Support Tube Chute CrankBracket Carriage Bolt Chute Crank RODIdler Pulley Side Plate Right Side View Installing the Auger BeltMounting Plate TwistBolt Attaching Weight Tray to TractorSide Brace ChecklistHole with HEX Bolt Removed Truss Head Bolt X 1 SlottedHOW to USE Your Snow Thrower Know Your Snow ThrowerBefore Starting Customer Responsibilities Replacing Auger Belt Lift Release Cable AdjustmentSkid Shoe Adjustment Clutch Disengagement AdjustmentStorage Recommendations Removing the Spiral Auger HousingProblem Cause Correction Additional Parts to Remove AT END of SeasonRepair Parts for Model 486.24839 40 Snow Thrower Part 26 731-1379A 34 741-0493AAo \ \ Bracket, Chute Housing, TriggerDESCRtPTION QTYPage Page MY-HOME