Craftsman 486.24839 Installing CLUTCH/IDLER Assembly, ROD Operated Attachment Clutches

Page 9

INSTALLING CLUTCH/IDLER ASSEMBLY

This section covers the installation of the Clutch/Idler assembly to tractors with attachment clutches that are either rod operated (p, 9), cable operated (p. 10) or electric (p. 12). Use the appropriate instructions for your tractor.

ROD OPERATED ATTACHMENT CLUTCHES

Move the attachment clutch lever on the dash panel to the disengaged (down) position.

Screw the trunnion onto the end of the snow thrower engagement rod as shown in figure 11.

Locate the clutch arm which is found underneath the right hand side the tractor, just to the inside of

the suspension arm. This is the arm that the mower clutch rod was connected to. The arm moves

forward and backward as the attachment clutch lever on the dash panel is moved.

Position the engagement rod to the inside of the clutch arm and insert the drilled end of the rod

through the arm. Secure with a 5/64" hairpin cotter. See figure 11.

ENGAGEMENTROD

TRACTOR'SCLUTCH ARM

/

5/64" HAIRPIN COTTER

\

SUSPENSION ARM

FIGURE 11

RIGHT SIDE VIEW

Be sure that the loose end of the engagement rod is lifted up toward the front of the tractor (as shown in figure 12) when performing the next operation.

You can temporarily support the rod using a rubber band tied to the engine pulley keeper.

Attach the snow thrower's clutch/idler assembly to the tractor frame by sliding the notched arms at the rear of the assembly onto the two shoulder bolts assembled to the inside of the tractor frame. Lift the front of the assembly, fitting the sides into the R.H. and L.H. hanger brackets. Attach the assem- bly to the brackets using two pivot lock pins and 1/8" hairpin cotters. See figure 12.

1/8" HAIRPIN COTTER

PIVOT LOCK PIN

ENGAGEMENT

ROD

FIGURE 12

RIGHT SIDE VIEW

Make sure the attachment clutch lever on the dash panel is in the disengaged (down) position.

Pivot the upper idler arm so that it rests against the stop bolt and is pointing toward the front as shown in figure 13. Screw the trunnion along the threads of the engagement rod until it is aligned at the front end of the idler arm slot. Attach the trunnion to the slot using the 3/8" flat washer and a 5/64" hairpin cotter. See figure 13.

IDLER ARM

3/8" FLAT

_ WASHER

5/64" HAIRPIN COTTER

FIGURE 13

RIGHT SIDE VIEW

Image 9
Contents Craftsman Wheel Weight Tire ChainsDrift Cutter Bars Become alert!! Your safety is involved Not Shown Actual Size Shown Actual SizeSpare Parts BAG REF. QTY DescriptionCarton Contents Tools Required for Assembly Assembly of Side Plates to TractorRemoval of Parts from Carton Items Removed from TractorRight Side View WasherInstalling Shoulder Bolts ROD Operated Attachment Clutches Installing CLUTCH/IDLER AssemblyCable Operated AnACHMENT Clutches Engine PulleyHair Cotter PIN Tractors Clutch CableEngine Hairpin Cotier Pivot Lock PINKeeper Engine 4PULLEYTensioning Chain Electric AnACHMENT ClutchesChain Side View of BottomAssembly of the Snow Thrower Bracket Carriage Bolt Chute CrankChute Crank ROD Crank Support TubeMounting Plate Side Plate Right Side View Installing the Auger BeltTwist Idler PulleyBolt Attaching Weight Tray to TractorHole with HEX Bolt Removed Truss Head Bolt ChecklistX 1 Slotted Side BraceHOW to USE Your Snow Thrower Know Your Snow ThrowerBefore Starting Customer Responsibilities Skid Shoe Adjustment Lift Release Cable AdjustmentClutch Disengagement Adjustment Replacing Auger BeltProblem Cause Correction Removing the Spiral Auger HousingAdditional Parts to Remove AT END of Season Storage RecommendationsRepair Parts for Model 486.24839 40 Snow Thrower Part 26 731-1379A 34 741-0493AAo \ \ DESCRtPTION Housing, TriggerQTY Bracket, ChutePage Page MY-HOME