Craftsman 486.24516 HOW to Start Your Chipper MAC, HOW to USE Your Chipper MAC, Before Starting

Page 20

BEFORE STARTING

•Your Chipper Vac System engine is shipped without oil or gasoline. Service the engine with oil and gas as instructed in the separate engine manual.

•Inspect the Vac System to make sure all covers (rear door, hardtop boot, elbow, hose adapter, hose and deck adapter are properly attached.

•Check tires for proper inflation (12 - 14 Ibs).

with the engine running, or while the engine

WARNING: Never fill fuel tank indoors, or is hot. Do not smoke while filling tank.

HOW TO STOP YOUR CHIPPER VAC

•To stop engine, move the throttle control lever to the OFF position.

•Disconnect spark plug wire from plug to prevent accidental starting while equipment is unattended or is being worked on.

CAUTION:areas are hot!r_e muffler and adjacent

HOW TO START YOUR CHIPPER MAC

engine without all covers being properly

WARNING: Never start or run the attached to the blower housing and cart.

•Check oil and gas in Chipper Vac engine.

•Attach spark plug wire to spark plug.

•Move choke lever on engine to CHOKE position. (A warm engine may not require choking.)

•Move throttle control lever on engine to FAST position.

•Grasp starter handle and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly.

•Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Let rope rewind

slowly. Do not let starter handle snap back against starter.

•Repeat instructions in two preceding paragraphs until engine fires. When engine starts, move choke control gradually to RUN position.

HOW TO USE YOUR CHIPPER MAC

&may be affected with the addition of an accessory or an attachment. Be aware of

changing conditions on slopes,

•Inspect the Chipper Vac to make sure all covers (rear door, hard top boot, elbow, chipper chute with tamper plug, hose adapter (nozzle), hose and deck adapter are properly attached.

•Check tires for proper inflation (12 - 14 Ibs).

•Check oil and gas in Chipper Vac engine.

•Begin operation at low speed, adjusting forward speed to match grass height and/or moisture condition to prevent clogging.

•Do not attempt to vacuum up any material other than

vegetation found in a normal yard, such as light

branches, leaves, twigs, etc.CAUTION: Vehicle braking and stability

WARNING: Should your Chipper Vac

&become clogged, shut off tractor and Chipper Vac engines. Before attempting

to unclog, remove wire from spark plug to prevent accidental starting.

•To empty cart, shut off tractor engine and set brake.

•Shut off Chipper Vac engine.

•Remove rear door from cart.

•Release latch lock lever on tongue and tip cart back. See figure 36.

sure that no one is near the cart before

CAUTION: To avoid possible injury, be releasing the latch lock lever.

'T"

•Lift rear of hard top and secure it in the upper raised position with right and left prop rods.

•Using a rake or suitable tool, pull grass clippings and/ or leaves out of cart.

•After cart is emptied, close hard top, tip cart for- ward and secure it to the tongue. Reattach rear door and hardtop boot.

FIGURE 36

2O

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Lcrrftshrni Limited Warranty on Battery Limited Warranty on Craftsman Powered Tractor AttachmentsPage To Avoid Serious Injury 486.24516 Date of PurchaseShown Full Size Not all parts in this list will be used for any one tractor Carton Contents Tools Required for Assembly Removal of Parts from CartonsAssembling the VAC System HEX BoltSkid Plate WasherHEX Bolt Axletongue Lock WasherTongue Ihex NUT 114HEX NUT WasherdumphandleLock HEX Washer NUT Lock NUTHexnut TIE ROD HEX BoltDoor Latch Left Hand Nylock NUT Nylon WasherElbow Nylon Washer Supports HEX BoltUSE PRE BOLTS, Lock Washers HEX Lock Nuts Impeller housing, securing it with the three knobs Chipper Chute AssemblyHose Adapter Nozzle 25TARP StrapAssembling the Deck Adapter #62468 to the Mower Deck Deck Adapter Lock NutsNylon Mower Deck Washers GO Directly to the Operation Instruc Tions onFor 1990 and Newer Murray Tractors with a 38 or 40 Deck For 1990 and Newer Murray Tractors with a 46 DeckTions Which are Located on Angle Bracket HEX Lock NUT Nylon Washer MountingKnow Your VAC System HOW to Start Your Chipper MAC HOW to USE Your Chipper MACHOW to Stop Your Chipper VAC Before StartingUsing the Chipper Chute Engine Maintenance CleaningCustomer Responsibilities Beforeeach USESharpening or Replacing Chipper Blades Nylock NutsProblem Possible CausesPart QTY Description 62458 Tailgate Reinforcement BracketSupport QT¥ DescriptionAdapter #62468 42TRACTOR39 24582 3 Hinge, Poly Top 4336429-0241A Harness, Wire 731-1613 Cover, Switch Housing Assy.InnerHousing Assy.Outer 712-3046 Nut, Hex Jam 5116o18Thd Spacer, Housing=CD Page Page Au Canada pour service en franais Get it fixed, your home or ours

486.24516 specifications

The Craftsman 486.24516 is a versatile lawn mower designed to cater to the needs of homeowners who seek efficiency and ease of use in lawn maintenance. This model combines robust features with innovative technologies, ensuring that it delivers outstanding performance on the job.

One of the standout features of the Craftsman 486.24516 is its powerful engine. Equipped with a reliable gas engine, it provides ample power for mowing through thick grass and tackling uneven terrain. The engine is engineered for efficiency, offering a balanced performance that ensures longevity and reduced maintenance needs over time.

The mowing deck is another key element of this model. The Craftsman 486.24516 features a wide cutting deck, which allows for a more efficient mowing process by cutting a larger swath of grass in a single pass. The adjustable height settings enhance this functionality, enabling users to customize their cutting height according to their lawn’s requirements. This is particularly useful for maintaining a healthy lawn, as different grass types may thrive at different cutting heights.

For added convenience, the Craftsman 486.24516 comes with an easy-start mechanism. This eliminates the hassle of traditional pull-start engines, allowing users to engage the mower with minimal effort. The model also includes ergonomic handles, designed for comfort and stability, ensuring that users can maneuver the mower effortlessly while reducing fatigue during extended use.

In terms of technology, the Craftsman 486.24516 incorporates advanced features that enhance usability. The mower is designed with a mulching capability, allowing grass clippings to be finely chopped and returned to the soil as natural fertilizer, promoting healthier lawn growth while reducing yard waste. Additionally, the side discharge option provides flexibility, allowing users to choose how they wish to handle clippings based on their lawn care preferences.

Durability is a hallmark of the Craftsman brand, and the 486.24516 is no exception. Constructed with high-quality materials, the mower is built to withstand the rigors of regular use. Its frame and components are designed to resist wear and tear, ensuring that the mower remains reliable throughout its lifespan.

Overall, the Craftsman 486.24516 is a dependable choice for homeowners looking to simplify their lawn care routine. With its powerful engine, adjustable cutting deck, easy-start technology, and durable construction, this lawn mower stands out as a top contender for efficient lawn maintenance.
Top Page Image Contents