Craftsman 247.776350 manual Stopping Engine, Gas And Oil Fill-up, Oil one 20-oz. bottle included

Page 9

TamperUse the tamper to assist in feeding branches into the chipper chute.

Hopper

Leaves, twigs and branches up to 1/2-inch in diameter may be placed into the hopper for shredding.

IMPORTANT: Never place branches with a diameter greater than 1/2-inch in the hopper. Doing so can result in serious damage to your unit'sshredder blade, flails or impeller.

Engine

NOTE: In the state of California, the 110000 series engines covered in this manual are certified by the California Air Resources Board to meet emissions standards for 250 hours. Such certification does not

grant the purchaser, owner or operator of this engine any additional warranties with respect to the performance or operational life of this engine. This

engine is warranted solely according to the product and emissions warranties stated elsewhere in this manual.

Bore

2-11/16

in.

(68 mm)

Stroke

2-13/64

in.

(56 mm)

Displacement

12.48cu.

in.(206cc)

IMPORTANT:For practical operation, the horsepower loading should not exceed 85% of rated horsepower. Engine power will decrease 3-1/2% for each 1,000 feet (300 meters) above sea level and 1% for each 10° F (5.6 °C) above 77° F (25 ° C). Engine will operate satisfactorily at an angle up to 15 degrees.

Throttle Lever

The throttle lever controls the engine speed and stop function.

Choke Control

The choke control closes the choke plate on the carburetor and aids in starting a cold engine.

Starter Handle

The starter handle is located on the engine. Pull the starter handle to start engine.

Stopping Engine

Move throttle control lever to STOP position. See Figure 7.

 

WARNING: When moving throttle control

,_

lever, be careful

of heated surfaces on muffler

 

guard.

 

A

CAUTION:

Never stop the engine by

,_.

moving the choke lever into the CHOKE position. Backfire, fire or engine damage could result.

Gas And Oil Fill-up

Oil (one 20-oz. bottle included)

IMPORTANT:The chipper shredder is shipped without oil in the engine.

Type of Oil

1.Refer to the chart below for proper grade of oil.

2.Use a high quality detergent oil classified "For service SF, SG,SH, SJ" or higher.

3.Do not use special additives.

Synthetic off meeting ILSAC GF-2, API certification and API service symbol with "SJ/CF Energy Conserving" or higher is an acceptable oil at all temperatures. Use of synthetic oil does not alter required oil change intervals.

SAE Viscosity Grades

30 iL

_5W-30, 10W-30

I

°F -20" O°' 20" 40°' 60°' 80°' 100°'

Starting temperaturerangeanticipated before nextoil change

*CAUTION: Air cooled engines run hotter than automotive engines. The use of non-synthetic multi-viscosity oils (5W- 30, 10W-30 etc.) in temperatures above 40°F will result in higher than normal oil consumption. When using a multi- viscosity oil, check oil level more frequently.

**CAUTION: SAE 30 oil, if used below 40°F, will result in hard starting and possible engine bore damage due to inadequate lubrication.

Remove oil fill dipstick.

With the Chipper Shredder on level ground, use a funnel to fill engine with oil to FULL mark on dipstick. Capacity is 20 oz. (0.6 liter). Be careful not to overfill. Overfilling will cause the engine to smoke profusely and will result in poor engine performance. The oil bottle packaged with your Chipper Shredder contains 20 oz. of oil.

Before operating the chipper shredder, check the oil level as follows:

Wipe the dipstick with a clean cloth and reinsert it in the oil fill tube.

Figure 7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Safety Operation Maintenance Storage Espa5ol, p Horse PowerModel No Sears, Roebuck And Co., Hoffman Estates, IL 60179 U.S.ALimited Warranty on Craftsman Chipper Shredder ContentThis Warranty does not cover MY-HOMETraining Allowmachinetocootatleast5minutes Beforestoring OperationEngine Emissions Compliance Label After July 1, 2000, Look For Emissions Compliance Period OnLoose Parts In Carton SeeFigure1 Removing Unit From CartonRaising the Chipper Chute Lowering the Chipper ChuteEmptying the Debris Collection Bag Attaching The Debris Collection BagKnow Your Chipper Shredder Meets Ansi safety standardsEnginej Operating Controls See FigureStopping Engine Gas And Oil Fill-upOil one 20-oz. bottle included Gasoline Starting EngineFull Type of FuelChoke ShreddingCleaning the Reduction Chamber Discharge Chute Shredder Screen HousingChipping Knob Cover Cartridge Pre-cleaner Air Cleaner Air CleanerCustomerResponsibilities LubricationCleaning Engine Spark PlugChanging Oil Spark Plug Wire Disconnecting Spark PlugReplacing the Chipper Blades Replacing the Shredder BladeCarburetor Adjustment Chipper Shredder EngineRemedy Problem CauseSears Emission Control Defects Warranty Coverage Sears Craftsman 7.5 H.P. Chipper Shredder Model Inlet Guide Part DescriptionPage 968 365 633A D 163 137 276 127 130 %5 276Q467 633Sears Craftsman 7.5 H.P. Chipper Shredder Model 2271 5z31524 334 8511330REPA,MANOA, 1 48S.ORTBLOCK Refi 699508 399269 299819 Refi 595 523 524 Engine Labels 777S30180Esta garantia no cubre Garantia limitada de la cortadora trituradora CraftsmanPreparacion Dejarespacioparaladilataci6ndel Combustible Dejequeel motorseenfrieporlomenosdosPage Piezas sueltas en la caja VerFigura1 Extraccibn de la unidad de la cajaDeslizamiento hacia abajo del canal de la cortadora Deslizamiento hacia arriba del canal de la cortadoraColocacibn de la bolsa de recoleccibn de desechos Vaciado de la bolsa de recoleccibn de desechosHebina de seguric Conozca las propiedades de la cortadora trituradora Controles de funcionamiento vetFigura6Cumple con los estbndares de seguridad de Ansi Carga de gas y aceite Detencibn del motorEncendido del motor GasolinaAdvertencia Sea sumamente Trituracibn NosernecesariaVerFigura10Corte Limpieza de la tolvaLa horquilla Limpieza del canal de reduccibnLubricacibn ResponsabilidadesdelclienteFiltro de aire PerillaLimpieza del motor Bujia de encendidoCambio de aceite Reemplazo de la hoja de la trituradora Reemplazo de las hojas de la cortadoraDesconexibn de la bujia Silenciador Filtro deairTuercas con Ajuste del carburadorReborde Igura zoCortadora trituradora Fast Causa RemedioEncontrada en UR motor certificado Acuerdo De Proteccibn Para Reparaciones Repair Protection AgreementsMY-HOME Our HomeCanada

247.776350 specifications

The Craftsman 247.776350 is a highly versatile and efficient lawn tractor designed to deliver exceptional performance and comfort for all your mowing needs. This machine is renowned for its robust build quality and reliability, making it a popular choice among homeowners seeking a reliable partner for lawn maintenance.

One of the standout features of the Craftsman 247.776350 is its powerful 19 HP Briggs & Stratton engine. This engine ensures high performance, allowing the tractor to tackle various terrains with ease, including hills and uneven ground. The engine is paired with a hydrostatic transmission, which provides seamless speed control and enhances maneuverability. Users can adjust their speed without the necessity of manual shifting, resulting in a more user-friendly experience.

The cutting deck on the Craftsman 247.776350 is 42 inches wide, which enables efficient mowing over larger areas. This deck is equipped with a three-blade design that delivers a clean and even cut, helping to ensure a healthy lawn appearance. The cutting height can be easily adjusted between multiple positions, catering to various grass types and seasonal growth differences.

Comfort is a top priority with the Craftsman 247.776350, which features an ergonomic operator station. The high-back seat offers ample support during long mowing sessions, while the foot pedal control system makes it easy to engage and disengage the cutting deck without straining.

In terms of technology, the Craftsman tractor is equipped with features designed to enhance usability. The integrated LED headlights provide visibility during early morning or late evening tasks, ensuring safe operation regardless of the time of day. Additionally, the tractor comes with a mulching capability, allowing users to finely chop grass clippings for natural fertilization of the lawn.

Maintenance is simplified with the Craftsman 247.776350; the deck is designed for easy access, and it is recommended to use the washout port for efficient cleaning after mowing. This feature helps to maintain the longevity of the machine and ensures optimum performance.

In summary, the Craftsman 247.776350 combines power, comfort, and advanced technology into a practical lawn tractor. Its strong Briggs & Stratton engine, hydrostatic transmission, and user-friendly features make it an excellent choice for homeowners looking to keep their lawns well-maintained with minimal effort. Whether you have a small yard or a larger property, this lawn tractor offers the reliability and efficiency needed for a beautifully manicured lawn.
Top Page Image Contents