Craftsman 247.77586 GAS and OIL FILL-UP, Oil Packed with unit, Remove cap, Fill gas, Gasoline

Page 9

Stopping Engine

Move throttle control lever to STOP position. Disconnect spark plug wire and move away from spark plug to prevent accidental starting.

WARNING: Before using your chipper- shredder, again refer to the safety rules on

page 3 and 4 of this manual. Always be careful.

3. GAS AND OIL FILL-UP

Oil (Packed with unit)

Only use high quality detergent oil rated with API service classification SF, SG or SH. Select the oil's viscosity grade according to your expected operating temperature. Follow the chart below.

Colder _ 32°F_ Warmer

5W30 [ SAE 30

NOTE: Although multi-viscosity oils (5W30, 10W30, etc.) improve starting in cold weather, these multiviscosity oils will result in increased oil consumption when used above 32°F. Check the oil level more frequently to avoid possible engine damage from running low on oil.

Fill engine with oil as follows.

•Remove oil fill dipstick. See figure 9

Remove

dipstick

Remove cap

and fill

oil

and fill gas

With chipper-shredder on level ground, use a funnel to fill engine with oil to FULL mark on

dipstick. Capacity is approximately 26 ounces. Be careful not to overfill.

Check oil level.

oAdd oil if necessary.

oReplace dipstick and tighten.

NOTE: Do not overfill. Oil bottle packed with unit contains 26 oz. of oil.

Gasoline

WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are

empty. Use fresh fuel next season. See STORAGE instructions for additional information. Never use

engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Fill gas tank with gas as follows.

•Remove fuel cap.

•Make sure the container (from which you will pour the gasoline) is clean and free from rust or foreign particles. Never use gasoline that may be stale from long periods of storage in the container.

•Fill fuel tank with clean, fresh, lead-free

automotive gasoline. DO NOT use Ethyl or high octane gasoline. See figure 9.

. Replace fuel cap.

WARNING: Do not fill closer than 1/2 inch of top of fuel tank to prevent spills and to allow for fuel expansion. If gasoline is accidently spilled, move chipper-shredder away from area of spill. Avoid creating any source of ignition until gasoline vapors have disappeared.

Check the fuel level periodically to avoid running

out of gasoline while operating the chipper- shredder.

If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit

before it can be restarted. Refer to Removing the Flail Screen in SERVICE AND

ADJUSTMENT section.

Figure 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Craftsman One-Year Warranty on Craftsman Chipper-Shredder General Operation Children ServiceYour Responsibility Savetheseinstructions For FuturereferenceSafety Glasses Bottle Oil Loose PartsChipper Chute Tools Required Disconnecting Spark PlugHex Bolt Hinge HopperAttaching the Catcher BAG Attaching the Chipper ChuteLift hopper up Pull release bar Weld Stud Hex Nut Discharge Chute Brace?per Assembly Meets Ansi Safety StandardsOperating Controls RlreaSe Starter HandleOil Packed with unit GAS and OIL FILL-UPRemove cap Fill gasStarting Engine Using Your CHIPPER-SHREDDERStopping Engine Move choke to on positionGeneral Recommendations Shred material upto 1 inch in diameterChute till the engine has completely stopped Engine Maintenance CleaningMaintenance Customer ResponsibilitiesFeeler Gauge Zrk Plug Spark PlugLubrication Removing the Flail ScreenMuffler Chipper Blades Sharpening or Replacing the BladesShredding Blade Sharp EdgeEngine Speed Adjusting CarburetorTires GroundCHIPPER-SHREDDER EngineOther Problem Possible Cause Corrective Action Sears Craftsman 8 H.P. CHIPPER=SHREDDER Model Sears Craftsman 8 H.P. CHIPPER-SHREDDER Model KEY Description Ooo 3OO Lever Clamp RPM8OO Carburetor Sears Craftsman CHIPPER-SHREDDERPage Sears Crrftsmrn Producto Segura en este Manual. AI igual Operacion GeneralPara Referencia Futura SU ResponsabilidadPiezas Sueltas Extraiga LA Astilladora Desmenuzadora DE LA CajaCanaleta de la astilladora Tolva Canaleta de descargaFijacion DE LA Canaleta DE Descarga Herramientas RequeridasLA Tolva Orificio Tuerca hexagonalFijacion DE LA Canaleta DE LA Astilladora Fijacion DE LA Bolsa ColectoraPernc hexagonal Conozca SU ASTILLADORA-DESMENUZADORA Controles DE OperacionCumple CON LAS Normas DE Seguridad DE Ansi Mds Frio Mds Caliente Llenado DE Gasolina Y AceiteDetencion DEL Motor Arranque DEL MotorUSO DE SU ASTILLADORA- Desmenuzadora Descenso DEL Conjunto DE LA TolvaFigura Recomendaciones GeneralesMantenimiento DEL Motor LimpiezaFechas DE Servicio Aceite de motorCubierta Base Tuerca Para prestar servicio al filtro de airePapel De Filtro De Espuma Si Asi EquipadoExtraccion DEL Tamiz DE LA Desgranadora LubricacionSilenciador Tamiz de laCaho Afilado O Reemplazo DE LAS CuchillasCuchillas de la astilladora Cuchilla de la desmenuzadoraAjuste DEL Carburador NeumaticosVelocidad DEL Motor SueloASTILLADORA-DE Smenuzadora MotorOtro El motor no arranca Problema800-659-7O84

247.77586 specifications

The Craftsman 247.77586 represents a blend of innovative engineering and practical design tailored for homeowners and garden enthusiasts. This versatile tool, primarily a snow blower, is optimized for efficient snow removal, making it an essential asset during winter months when heavy snowfall can pose challenges.

One of the standout features of the Craftsman 247.77586 is its powerful 24-inch clearing width, which allows users to quickly clear driveways, sidewalks, and patios. The machine is equipped with a robust 208cc engine that delivers reliable performance in various snow conditions. This engine provides ample power to move heavy, wet snow, ensuring users can tackle even the toughest of winter storms with confidence.

The Craftsman 247.77586 is designed with user comfort and convenience in mind. Its ergonomic handles are adjustable, allowing for a customizable grip that can be adjusted to suit different users' preferences. Furthermore, the snow blower features a hydraulic chute control, enabling users to easily adjust the direction of snow discharge without needing to halt their operations. This tool can throw snow up to 30 feet away, helping prevent the accumulation of snow in areas that have already been cleared.

The unit is equipped with a 6-speed transmission, comprising 5 forward speeds and 1 reverse, allowing for efficient maneuvering to suit different snow depths and types. This feature is particularly advantageous when navigating tricky terrain or when following previously cleared paths.

Another notable characteristic of the Craftsman 247.77586 is its durable construction. Built with high-quality materials, this snow blower is designed to withstand the rigors of frequent use during harsh winter months. The heavy-duty impeller and auger work together effectively to break down large snow piles, while the sturdy chassis ensures stability and resilience.

Additionally, the Craftsman 247.77586 boasts easy maintenance features. Access points for oil changes and spark plug replacements are conveniently located, allowing users to keep the equipment in top shape with minimal hassle. This attention to maintenance eases the ownership experience, ensuring that performance remains at an optimal level throughout the snow season.

In summary, the Craftsman 247.77586 is not just a snow blower; it is a reliable winter partner. With its powerful engine, substantial clearing capabilities, user-friendly adjustments, and durable construction, it is designed to tackle the demands of winter efficiently. For anyone seeking to maintain a clear outdoor space during snowfalls, the Craftsman 247.77586 stands out as a dependable choice.
Top Page Image Contents