Craftsman 107.2777 manual General Operating Safety, Ignition Switch, Hour Meter, Parking Brake

Page 11

Mower Height of Cut Adjustment

To adjust cutting height, rotate the turn crank clockwise to raise the mower deck and counterclockwise to lower the mower deck.

ignition Switch

The ignition switch starts and stops the engine; it has three positions:

OFF Stops the engine and shuts off the electrical system.

RUN Allows the engine to run and powers the electrical system.

START Cranks the engine for starting.

NOTE." Never leave the ignition switch in the RUN posi- tion with the engine stopped. This drains the battery.

B Hour Meter

The hour meter measures the number of hours the key has been in the RUN position. The hour meter will flash an oil change indicator at 5 hours, and a lubrication reminder every 50 hours. These reminders will automati- cally reset themselves.

NOTE." The hour meter will register the passage of time when the key is in the RUN position, even if the engine is not running.

PTO Switch

The PTO (Power Take-Off) switch engages and disen- gages an electric clutch attached to the engine crank- shaft. This electric clutch drives and stops the mower deck. To turn the mower on, pull the switch UP. Push the switch DOWN to turn the mower off. Note that the opera- tor must be seated firmly in the rider seat for the PTO to function.

Transmission Release Levers

The transmission release levers deactivate the transmis- sions so that the unit can be pushed by hand. See PUSHING THE UNIT BY HAND for operational informa- tion.

Seat Adjustment Knob

The seat can be adjusted forward and backward. Tip the seat forward, loosen the adjustment knob, slide the seat to the desired position, and tighten the knob.

Fuel Tank

To remove the cap, turn counterclockwise.

Parking Brake

DRIVE Releases the parking brake.

PARK Locks the parking brake.

Pull the parking brake lever up to engage the parking brake (PARK position). Move the lever fully down to dis- engage the parking brake (DRIVE position).

NOTE: To start the unit the parking brake must be in PARK position.

GENERAL OPERATING SAFETY

Before first time operation:

•Be sure to read all information in the Safety and Operation sections before attempting to operate this rider and mower.

•Become familiar with all of the controls and how to stop the unit.

•Drive in an open area without mowing to become accus- tomed to driving the unit.

,WARNING

If you do not understand how a specific control functions, or have not yet thoroughly read the CONTROL FUNCTIONS section, do so now.

Do NOT attempt to operate the rider without first

becoming familiar with the location and function of ALL controls.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operating Instructions Manual and follow all its Safety RulesFor answers to your questions about this Product, callPTS=I Limited Warranty on BatteryIdentification General Operation Slope Operation EmissionsService and Maintenance Height Adjustment Safety & Operation DecalsIIIlillllllllll Iliiillililllil 2s u Start To push Unit off the crateDrive positions levers pushed Charging informationGround Speed Levers Throttle Control Control FunctionsLeft SpeedLever Parking Brake General Operating SafetyIgnition Switch Hour MeterDo not Start or Stop on a Slope Checks Before StartingFuel Recommendations Avoid over=filling and wipe up any spillsMowing Emergency StoppingStopping the Rider & Engine Starting the EngineLevers Gradually Forward TravelSmooth Travel Forward Travel PracticePractice Turning in Place Practice Turning Around a CornerExecuting Turns Turning In Place Executing an End=Of=Row Zero TurnMower Deck Removal InstallationInstalling the Mower Deck Each Use Fall Hours Maintenance ScheduleBefore Every Spring 100 200 Pressure Clean Debris from Rider and Engine CompartmentClean Debris from Engine Cooling Areas and AIR Filter Checktire PressureLubricating Rider Service Interval 25 hoursWorkbench Clean Deck Check / Replace Mower BladesService interval 200 Hours Cleaning the Battery and CablesCheck Rider Safety System Operational Safety ChecksAdjustment Nut Check / Adjust PTO ClutchAdjustment Window Qty , one shown B. Adjustment Nut Oil Drain Tube Check Engine OIL LevelChange Engine OIL Change Engine OIL & FilterReplace AIR Filter Air Filter Cover & Knob Foam Pre-CleanerSpark Plug ReplaceSpark Plug Replace Fuel FilterSpeed Balancing Adjustment Seat AdjustmentsGround Speed Control Lever Adjustment Battery Charging Cutting Height AdjustmentPTO Clutch Adjustment Brake AdjustmentOrient Blades Side-to-Side Mower Deck Leveling AdjustmentsFront To Back Leveling Mower Belt ReplacementMower Drive Belt Replacement Arbor Drive Belt ReplacementSTO RAG E Poorly Troubleshooting RiderTo avoid serious injury, perform maintenance on Hard orExcessive mower vibration Troubleshooting the MowerBelt installed incorrectly Rider will notZT 7OOO Garantia Limitada DE LA Bateria PTS-1Garantia Limitada DEL Equipo Montable DE Craftsman Transporte Aliviacenaiviiento Operacion EN Cuestas Sistema DE EncendidoServicio y Mantenimiento Servco Y MANTENilVIENTOOperacion Identificaci6n Llaves Manual del Motor Recolector de Hierba con Bolsa Gemela Faro delanteroFresca OperadorPalancas De Velocidad Control De Aceleraci6n DE ControlAhogador Interrupter PTO Seguridad General DE OperacionInterrupter de Encendido Medidor de HorasNunca permita que pasajeros se paseen en la unidad ADVERTENCIA- ReiviolquesVerificaciones Antes DE Arrancar Recomendaciones DE CombustibleEmpujar EL Tractor MANUAL- Mente Paro DE EmergenciaDetener EL Tractor Y EL Motor Arrancar EL MotorManejo Hacia Manejo en Adelante PR. ,CTICA DE IvianejoTraslado sin prob= LemasPrctica de Vuelta en el Lugar Prbctica de dar Vuelta en una EsquinaEjecutar un Giro Cero al Final de la Fila Vuelta en el Mismo LugarInstalar o quitar la podadora Remocion E Instalacion DE LA Cubierta DE LA PodadoraQuitar la Cubierta de la Podadora Instalar la Cubierta de la PodadoraPrimavera AntesCada otoSo 100 200 Cada UsoIntervalo de Servicio 25 horas DEL Compartimiento DEL MotorTRO DE AIREA. Rejilla de Admisi6n Aceite LubricacionFigura 20. Instalaci6n del Aspa OperacionSi la unidad no pasa una prueba de seguridad Intervalo de Servicio 200 horasPRUEBA4 -VERIFICACIONDEFRENODEASPAS VERIFICAR/AJUSTAR Embrague DEL PTO Nivel DE Aceite DEL Motor Cambiar EL Aceite DEL MotorVerificar Nivel DE Aceite DEL Motor Cambiar Aceite DEL Motor Y FiltroTapa y Perilla del Filtro de Aire Pre-Limpiador de Espuma Reeiviplazar EL Filtro DE AireFiltro DE Aire Limpiador DEL Filtro DE AireReeiviplazar Filtro DE Gasolina Reeiviplazar BUJiAAjuste DE Balanceo DE Velocidad Ajustes AL AsientoAjuste DE Palanca DE Control DE VelocidadRecarga DE LA Bateria Ajuste DE LA Altura DE CorteAjuste DEL Embrague DEL PTO Ajuste DEL FrenoTomillo Taptite Rampa Ajuste DE Nivel DE LA Cubierta DE LA PodadoraNivelado de un Lado a Otto Tuetca ExteriorSujecion Reemplazo DE Banda DE PodadoraNivelado de Adelante hacia Atrs Advertencia Incorrecto Diagn6stico del TractorEl cable de la bujJa y sujtelo lejos de la bujJa Causa RemedioDiagn6stico de la Podadora RepairParts ZT 7000 Frame, Body & Seat GroupBody & Seat Group FrameFrame, Body & Seat Group Frame, Body & Seat Group 26\ Engine GroupZT 7000 REF no Part QTY Description Engine Group 98646111 2o Carrier Group 986465 Transmission Group ZT 7000 Transmission Transmission GroupTransmission Group ZT 7000 1960027SM Controls Group ZT 7000 Footnotes Controls Group 986463Electrical Group ZT 7000 Electrical Group 986464 Wheels & Tires Group W986467 ZT 7000 Tires Group W986467 Decals Group D986467 ZT 7000 Decals Group D986467 203 Mower Deck Clutch & Support Group ZT 7000No Part no QTY Description Mower Deck Clutch Support Group 986473Mower Deck Height Adjustment Group ZT 7000 Mower Deck Height Adjustment Group 986471 Mower Deck Housing & Arbor Group ZT 7000 Mower Deck PTS Oil Pan/LubricationDESCRiPTiON Engine Parts2018j\ PTS Air Intake/Filtration QTY FltJfit Servicio de Jnstalaci6n de Sears Sears Installation ServiceRepair Protection Agreements Acuerdo de Protecci6n de Reparaciones@EARS

107.2777 specifications

The Craftsman 107.2777 is a versatile and robust tool that caters to both amateur and professional craftsmen alike. Designed for superior performance and user convenience, this power tool is a favorite among DIY enthusiasts and contractors who appreciate its reliability and feature-rich design.

One of the standout features of the Craftsman 107.2777 is its powerful motor, which delivers outstanding torque and efficiency. This motor is designed to handle a variety of tasks, from heavy-duty applications to delicate work, allowing users to seamlessly transition between different projects. The tool’s lightweight construction also means that it’s easy to maneuver, reducing fatigue during extended use.

The Craftsman 107.2777 boasts an ergonomic design that emphasizes user comfort. Its non-slip grip provides a secure hold, while the optimized balance ensures that the tool feels stable in hand. This is particularly advantageous for long periods of use, as it minimizes strain on the wrist and hand.

In terms of versatility, the Craftsman 107.2777 is equipped with an adjustable speed setting, allowing users to tailor the tool’s performance to match the requirements of specific tasks. This feature is especially useful when working with various materials, from wood and metal to plastic. The tool also comes with multiple attachments and accessories, enhancing its functionality for a wide range of applications.

Safety is a paramount consideration in the design of the Craftsman 107.2777. The tool features a built-in safety switch that prevents accidental activation, giving users peace of mind while working on projects. Additionally, the durable casing protects the internal components from dust and debris, helping to prolong the life of the tool.

Another key characteristic of the Craftsman 107.2777 is its compatibility with a range of Craftsman accessories. This means users can easily expand their tool collection without having to worry about compatibility issues, making this model a cost-effective choice for those looking to enhance their workshop capabilities.

Overall, the Craftsman 107.2777 stands out as a reliable, efficient, and user-friendly tool that meets the demands of any crafting job. Its combination of advanced features, ergonomic design, and safety considerations make it a must-have for both novice DIYers and seasoned professionals. Whether you’re tackling home improvement projects, building furniture, or working on repairs, the Craftsman 107.2777 delivers exceptional performance and versatility.
Top Page Image Contents