Craftsman 107.2777 manual Check Engine OIL Level, Change Engine OIL & Filter, Oil Drain Tube

Page 23

Engine Maintenance items

CHECK ENGINE OIL LEVEL

Service Interval: Before each use, and every 8 hours.

1.Turn the engine off, and set the parking brake to PARK.

2.Clean the area around the dip stick (C, Figure 25).

3.Remove the dip stick (C) and clean it with a paper towel.

4.Insert the dip stick back into the engine, but do not thread the cap back onto the tube (D).

5.Remove the dip stick and read the oil level. The oil level should be between the "F" and "L" marks (D). If not, add oil according to the oil recommendations chart (Figure 24).

Useoil classifiedAPI Service Class SG,

SH, SJ or betterwith SAEViscosity:

°F

i _,

0

20

,

/

60

u

100

-20

3_2 40

80

°C

-30

-18

-7

O

4

16

27

38

*Recommended: Syntbatic oils provide better starting below -10°E

Figure 24. Recommended Engine Oil

CHANGE ENGINE OIL

Service Interval: 100 Hours.

Oil Capacity: .95 Quarts with oil filter change.

Note: Change engine oil while the engine is warm. Run

the engine for a few minutes, then shut the engine off and allow it to cool from hot to warm.

1.Clean the area around the dip stick (C, Figure 25) and oil drain tube (A).

2.Remove the oil drain plug (A) from the end of the oil drain tube. Remove the dip stick (C). Allow ample time for complete drainage.

3.Reinstall the oil drain plug (A).

4.Fill the crankcase with oil. See CHECK ENGINE OIL LEVEL above.

CHANGE ENGINE OIL & FILTER

Service Interval: 200 Hours.

Oil Capacity: .95 Quarts with oil filter change.

Note: Change engine oil while the engine is warm. Run the engine for a few minutes, then shut the engine off and allow it to cool from hot to warm.

1.Clean the area around the dip stick (C, Figure 25) and oil drain (A).

2.Remove the oil drain plug (A) and and dip stick (C). Allow ample time for complete drainage.

3.Remove the oil filter (B). Discard the filter.

4.Turn the new filter upside down and fill with fresh engine oil. Allow the oil to seep into the new filter for two minutes.

5.Using a drop of oil on your finger tip, wet the rubber gasket on the bottom of the new filter.

Figure 25. Oil Change

A.Oil Drain Tube

B.Oil Filter

C.Dip Stick

D.Checking Oil Level

6.Dump the oil out of the filter and install the filter on the filter base. Turn the filter clockwise until the rub- ber gasket meets the filter base. Then turn 2/3 to 1 full turn more.

7.Reinstall the oil drain plug (A).

8.Fill the crankcase with oil. See CHECK ENGINE OIL LEVEL above.

9.Test run the engine to check for leaks. Stop the engine for 1 minute, then recheck the oil level.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Operating Instructions Manual and follow all its Safety RulesFor answers to your questions about this Product, callPTS=I Limited Warranty on BatteryIdentification General Operation Slope Operation EmissionsService and Maintenance Height Adjustment Safety & Operation DecalsIIIlillllllllll Iliiillililllil 2s u Start To push Unit off the crateDrive positions levers pushed Charging informationGround Speed Levers Throttle Control Control FunctionsLeft SpeedLever Parking Brake General Operating SafetyIgnition Switch Hour MeterDo not Start or Stop on a Slope Checks Before StartingFuel Recommendations Avoid over=filling and wipe up any spillsMowing Emergency StoppingStopping the Rider & Engine Starting the EngineLevers Gradually Forward TravelSmooth Travel Forward Travel PracticePractice Turning in Place Practice Turning Around a CornerExecuting Turns Turning In Place Executing an End=Of=Row Zero TurnMower Deck Removal InstallationInstalling the Mower Deck Each Use Fall Hours Maintenance ScheduleBefore Every Spring 100 200 Pressure Clean Debris from Rider and Engine CompartmentClean Debris from Engine Cooling Areas and AIR Filter Checktire PressureLubricating Rider Service Interval 25 hoursWorkbench Clean Deck Check / Replace Mower BladesService interval 200 Hours Cleaning the Battery and CablesCheck Rider Safety System Operational Safety ChecksAdjustment Nut Check / Adjust PTO ClutchAdjustment Window Qty , one shown B. Adjustment Nut Oil Drain Tube Check Engine OIL LevelChange Engine OIL Change Engine OIL & FilterReplace AIR Filter Air Filter Cover & Knob Foam Pre-CleanerSpark Plug ReplaceSpark Plug Replace Fuel FilterSpeed Balancing Adjustment Seat AdjustmentsGround Speed Control Lever Adjustment Battery Charging Cutting Height AdjustmentPTO Clutch Adjustment Brake AdjustmentOrient Blades Side-to-Side Mower Deck Leveling AdjustmentsFront To Back Leveling Mower Belt ReplacementMower Drive Belt Replacement Arbor Drive Belt ReplacementSTO RAG E Poorly Troubleshooting RiderTo avoid serious injury, perform maintenance on Hard orExcessive mower vibration Troubleshooting the MowerBelt installed incorrectly Rider will notZT 7OOO Garantia Limitada DE LA Bateria PTS-1Garantia Limitada DEL Equipo Montable DE Craftsman Transporte Aliviacenaiviiento Operacion EN Cuestas Sistema DE EncendidoServicio y Mantenimiento Servco Y MANTENilVIENTOOperacion Identificaci6n Llaves Manual del Motor Recolector de Hierba con Bolsa Gemela Faro delanteroFresca OperadorPalancas De Velocidad Control De Aceleraci6n DE ControlAhogador Interrupter PTO Seguridad General DE OperacionInterrupter de Encendido Medidor de HorasNunca permita que pasajeros se paseen en la unidad ADVERTENCIA- ReiviolquesVerificaciones Antes DE Arrancar Recomendaciones DE CombustibleEmpujar EL Tractor MANUAL- Mente Paro DE EmergenciaDetener EL Tractor Y EL Motor Arrancar EL MotorManejo Hacia Manejo en Adelante PR. ,CTICA DE IvianejoTraslado sin prob= LemasPrctica de Vuelta en el Lugar Prbctica de dar Vuelta en una EsquinaEjecutar un Giro Cero al Final de la Fila Vuelta en el Mismo LugarInstalar o quitar la podadora Remocion E Instalacion DE LA Cubierta DE LA PodadoraQuitar la Cubierta de la Podadora Instalar la Cubierta de la PodadoraPrimavera AntesCada otoSo 100 200 Cada UsoIntervalo de Servicio 25 horas DEL Compartimiento DEL MotorTRO DE AIREA. Rejilla de Admisi6n Aceite LubricacionFigura 20. Instalaci6n del Aspa OperacionSi la unidad no pasa una prueba de seguridad Intervalo de Servicio 200 horasPRUEBA4 -VERIFICACIONDEFRENODEASPAS VERIFICAR/AJUSTAR Embrague DEL PTO Nivel DE Aceite DEL Motor Cambiar EL Aceite DEL MotorVerificar Nivel DE Aceite DEL Motor Cambiar Aceite DEL Motor Y FiltroTapa y Perilla del Filtro de Aire Pre-Limpiador de Espuma Reeiviplazar EL Filtro DE AireFiltro DE Aire Limpiador DEL Filtro DE AireReeiviplazar Filtro DE Gasolina Reeiviplazar BUJiAAjuste DE Balanceo DE Velocidad Ajustes AL AsientoAjuste DE Palanca DE Control DE VelocidadRecarga DE LA Bateria Ajuste DE LA Altura DE CorteAjuste DEL Embrague DEL PTO Ajuste DEL FrenoTomillo Taptite Rampa Ajuste DE Nivel DE LA Cubierta DE LA PodadoraNivelado de un Lado a Otto Tuetca ExteriorSujecion Reemplazo DE Banda DE PodadoraNivelado de Adelante hacia Atrs Advertencia Incorrecto Diagn6stico del TractorEl cable de la bujJa y sujtelo lejos de la bujJa Causa RemedioDiagn6stico de la Podadora RepairParts ZT 7000 Frame, Body & Seat GroupBody & Seat Group FrameFrame, Body & Seat Group Frame, Body & Seat Group 26\ Engine GroupZT 7000 REF no Part QTY Description Engine Group 98646111 2o Carrier Group 986465 Transmission Group ZT 7000 Transmission Transmission GroupTransmission Group ZT 7000 1960027SM Controls Group ZT 7000 Footnotes Controls Group 986463Electrical Group ZT 7000 Electrical Group 986464 Wheels & Tires Group W986467 ZT 7000 Tires Group W986467 Decals Group D986467 ZT 7000 Decals Group D986467 203 Mower Deck Clutch & Support Group ZT 7000No Part no QTY Description Mower Deck Clutch Support Group 986473Mower Deck Height Adjustment Group ZT 7000 Mower Deck Height Adjustment Group 986471 Mower Deck Housing & Arbor Group ZT 7000 Mower Deck PTS Oil Pan/LubricationDESCRiPTiON Engine Parts2018j\ PTS Air Intake/Filtration QTY FltJfit Servicio de Jnstalaci6n de Sears Sears Installation ServiceRepair Protection Agreements Acuerdo de Protecci6n de Reparaciones@EARS

107.2777 specifications

The Craftsman 107.2777 is a versatile and robust tool that caters to both amateur and professional craftsmen alike. Designed for superior performance and user convenience, this power tool is a favorite among DIY enthusiasts and contractors who appreciate its reliability and feature-rich design.

One of the standout features of the Craftsman 107.2777 is its powerful motor, which delivers outstanding torque and efficiency. This motor is designed to handle a variety of tasks, from heavy-duty applications to delicate work, allowing users to seamlessly transition between different projects. The tool’s lightweight construction also means that it’s easy to maneuver, reducing fatigue during extended use.

The Craftsman 107.2777 boasts an ergonomic design that emphasizes user comfort. Its non-slip grip provides a secure hold, while the optimized balance ensures that the tool feels stable in hand. This is particularly advantageous for long periods of use, as it minimizes strain on the wrist and hand.

In terms of versatility, the Craftsman 107.2777 is equipped with an adjustable speed setting, allowing users to tailor the tool’s performance to match the requirements of specific tasks. This feature is especially useful when working with various materials, from wood and metal to plastic. The tool also comes with multiple attachments and accessories, enhancing its functionality for a wide range of applications.

Safety is a paramount consideration in the design of the Craftsman 107.2777. The tool features a built-in safety switch that prevents accidental activation, giving users peace of mind while working on projects. Additionally, the durable casing protects the internal components from dust and debris, helping to prolong the life of the tool.

Another key characteristic of the Craftsman 107.2777 is its compatibility with a range of Craftsman accessories. This means users can easily expand their tool collection without having to worry about compatibility issues, making this model a cost-effective choice for those looking to enhance their workshop capabilities.

Overall, the Craftsman 107.2777 stands out as a reliable, efficient, and user-friendly tool that meets the demands of any crafting job. Its combination of advanced features, ergonomic design, and safety considerations make it a must-have for both novice DIYers and seasoned professionals. Whether you’re tackling home improvement projects, building furniture, or working on repairs, the Craftsman 107.2777 delivers exceptional performance and versatility.
Top Page Image Contents