Craftsman 315.21213 manual To Bevel CUT with Your Miter SAW, Straight Crosscut Clamp

Page 20

STRAIGHT

CROSSCUT

• C-CLAMP

Fig, 26

Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board is placed against the fence, the board could collapse on the blade at the end of the cut, jamming the blade. See Figures 33 and 34.

•When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 31.

•Align cutting line on the workpiece with the edge of saw blade.

Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. See Figure 26.

_, WARNING: To avoid serious personal injury, keep your hands outside the no hands zone; at

least 3 in. from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

Before turning on the saw, perform a dry run of the cutting operation just to make sure that no problems win occur when the cut is made.

Grasp the saw handle firmly then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

Slowly lower the blade into and through the workpiece. See Figure 26.

Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops

blade from turning before removing the workpiece from the miter table.

BEVEL CUT

See Figures 27 and 28.

A bevel cut is made by cutting across the grain of the workpiece with the blade angled to the workpiece. A straight bevel cut is made with the miter table set at the zero degree position and the blade set at an angle

between 0°and 45°.

LEFT SIDE

RIGHTSIDE

LEFT

RIGHT

INDICATOR

INDICATOR

 

POINT

SCALE

MOUNTINGBRACKET

Fig. 27

TO BEVEL CUT WITH YOUR MITER SAW

•Pull out the lock pin and lift saw arm to its full height.

•Loosen the miter lock handle. Rotate the miter

lock handle approximately one-half turn to the left to loosen.

•Press the miter lock plate down with your thumb and hold.

•Rotate the control arm until the pointer aligns with zero on the miter scale.

•Release the miter lock plate.

Note: You can quickly locate zero by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the built-in

positive stop notches, located in the miter table frame.

•Tighten the miter lock handle securely.

_L, WARNING: To avoid serious personal injury, always tighten the miter lock handle securely

before making a cut. Failure to do so could result in movement of the control arm or miter table

while making a cut.

2O

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Read and follow Instructions before first useThis product Customer Help LineFull ONE Year Warranty Symbol Meaning Safety Alert SymbolRemove Wrenches and Adjusting Keys Double InsulationRules for Safe Operation Always Stay ALERT! Do not allow familiarity Rules for Safe Operation RPM Rating Volts, 60Hz-AC Only Input Amperes Net Weight 32 IbsNo Load Speed 5000 Inch Compound Miter Saw SAW Blade Bladewrench DustguideMiterlockhandle Combination Square Framingsquare PhillipsscrewdriverKnow Your Compound Miter SAW AMP MotorThroatplate LockplateTrigger Lock Spindle Lock ButtonSwrch Spindle LOCKBUIrONPositive Stops on Miter Table Bevel Lock KnobElectric Brake Miter FenceExhaust Port Dustguide To Install Blade Serious personal injuryPhillipsscrew Lower Bladeguard Lowerblade GuardbracketBlade FlatsOn Spindle WasherwithScrews Miter FenceSquaring Miter Table To the Fence Fence Miter Fence Miter Framing Table SquareMiter Fence Blade Miter Framing Table Square Mm HexkeySquaring the Blade to Miter Table Miter Lockhandle Correctview of Blade Squarewith MitertableDepth Stop Travel Pivot AdjustmentBevel Pivot Adjustment Applications Cutting with Your Compound Miter SAWTo Crosscut with Your Miter SAW CrosscuttingLeft Side Rightside Indicator Point Scale Mountingbracket To Bevel CUT with Your Miter SAWStraight Crosscut Clamp Bevel CUTCompound Miter CUT Bevelcut Fence Screw ClampTo Make a Compound CUT with Your Miter SAW Compound Mitercut Lamp45x 45COMPOUNDMITERCUT Support Long WorkpiecesLongworkpiece Workpiecesupports COMPOUND-ANGLE Settings for Popular Structures Pitch45.00 44.89 29.91 25.63 44.56 35.58 22.19 14.51 10.65 17.37 44.14 35.37 22.14 17.72 17.93 00 MCutting Crown Molding Laying Molding Flat on Miter TableBevel Angle Type of Cut Setting Left side, inside corner WrongCutting Warped Material Clamping Wide WorkpiecesGeneral LubricationExtension Cords Partmay create a hazard or cause product damageFigureA Craftsman Compound Miter SAW Model NumberDescription Quan Craftsman Compound Miter SAW- Model NumberKEY Part NO. Number FigureB KEY Part Number Description Quan Figure C Parts List for Figure C Figure D Parts List for Figure D Get it fixed, at your home or ourst

315.21213 specifications

The Craftsman 315.21213 is a versatile and reliable tool designed for both professional tradespeople and DIY enthusiasts. This compact and powerful rotary tool is known for its impressive performance and a wide array of features that make it essential for a variety of tasks.

One of the main features of the Craftsman 315.21213 is its powerful motor, which provides robust performance capable of handling different materials including wood, metal, and plastic. This rotary tool boasts a variable speed control that allows users to adjust the RPM according to their specific needs, ranging from delicate tasks like engraving at lower speeds to more demanding applications such as grinding or cutting at higher speeds.

The 315.21213 is compatible with a vast selection of accessories, enabling it to effortlessly switch between tasks. With its easy-to-use chuck system, users can quickly swap out bits and attachments without the need for additional tools, ensuring that workflow remains efficient and uninterrupted. The adaptability of this rotary tool makes it a favored choice for intricate projects like jewelry making, model building, and home improvement tasks.

In terms of technology, the Craftsman 315.21213 incorporates a lightweight design that enhances its portability. Weighing just enough to allow for extended use without causing fatigue, this tool is also designed with user comfort in mind, featuring an ergonomic grip that provides a secure hold even during prolonged projects.

Safety is another key characteristic of the Craftsman 315.21213. The tool is equipped with an integrated safety switch that prevents accidental starts, providing peace of mind when handling various tasks. Additionally, its ventilation system helps manage heat during prolonged use, protecting the motor from overheating and improving overall durability.

The Craftsman 315.21213 stands out for its reliable performance and exceptional versatility. Whether you are tackling a small craft project or larger renovation tasks, this rotary tool delivers the quality and consistency needed to achieve professional results. With a combination of power, adaptability, and user-friendly features, the Craftsman 315.21213 is a top choice for those seeking a reliable and efficient rotary tool.
Top Page Image Contents