Craftsman 315.21213 manual To Make a Compound CUT with Your Miter SAW, Compound Mitercut Lamp

Page 22

TO MAKE A COMPOUND CUT WITH YOUR MITER SAW

•Pull out the lock pin and lift saw arm to its full height.

•Loosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen.

•Press the miter lock plate down with your thumb and hold.

•Rotatethe control arm until the pointer aligns with the desired angle on the miter scale.

•Release the miter lock plate.

Note: You can quickly locate 0°, 22-1/2" left or dght, and 45" left or right by releasing the miter lock plate as you rotate the control arm. The miter lock plate will seat itself in one of the positive stop notches, located in miter table frame.

•Tighten the miter lock handle securely.

A WARNING: To avoid serious personal injury, always tighten the miter lock handle securely before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut.

Adjustments of the miter fence must be made to correspond to the desired angle of the bevel cut prior to tilting the saw arm. The fence is marked for 15°, 30°, or 45°. Loosen the fence screw on the miter fence, slide the fence to the desired position,

and retighten the fence screw. See Figures 28 and 29.

The 45°triangle on the miter fence provides for the maximum clearance required for adjusting the miter saw'sangle when making a bevel or com- pound cut.

•Loosen the bevel lock knob and move the saw arm to the left to the desired bevel angle.

•Bevel angles can be set from 0 ° to 45".

For your convenience there is a double scale located on the mounting bracket. See Figure 27. If one side becomes difficult to read as you move the saw arm to the left, simply refer to the other side. Align the indicator point for the side you choose with the desired angle.

•Once the saw arm has been set at the desired angle, securely tighten the bevel lock knob.

•Recheck miter angle setting. Make a test cut in scrap matedal.

Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board could collapse on the blade at the end of the cut, jamming the blade. See Figures 33 and 34.

When cutting long pieces of lumber or molding,

support the opposite end of the stock with a roller stand or with a work surface level with the saw

table. See Figure 31.

•Align the cutting line on the workpiece with the edge of saw blade.

•Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when _ossible. See Figure 29.

,_ WARNING: To avoid serious personal injury, always keep your hands outside the no hands

zone; at least 3 in. from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

COMPOUND

MITERCUT

C&LAMP

Fig. 29

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents This product Read and followInstructions before first use Customer Help LineFull ONE Year Warranty Remove Wrenches and Adjusting Keys Symbol MeaningSafety Alert Symbol Double InsulationRules for Safe Operation Always Stay ALERT! Do not allow familiarity Rules for Safe Operation No Load Speed 5000 Rating Volts, 60Hz-AC Only Input Amperes Net Weight 32 IbsRPM Inch Compound Miter Saw Miterlockhandle SAW Blade BladewrenchDustguide Combination Square Framingsquare PhillipsscrewdriverThroatplate Know Your Compound Miter SAWAMP Motor LockplateSwrch Spindle Trigger LockSpindle Lock Button LOCKBUIrONElectric Brake Positive Stops on Miter TableBevel Lock Knob Miter FencePhillipsscrew Lower Bladeguard Exhaust Port Dustguide To Install BladeSerious personal injury Lowerblade GuardbracketOn Spindle BladeFlats WasherwithSquaring Miter Table To the Fence Miter FenceScrews Miter Fence Blade Miter Framing Table Square FenceMiter Fence Miter Framing Table Square Mm HexkeySquaring the Blade to Miter Table Miter Lockhandle Correctview of Blade Squarewith MitertableBevel Pivot Adjustment Travel Pivot AdjustmentDepth Stop To Crosscut with Your Miter SAW ApplicationsCutting with Your Compound Miter SAW CrosscuttingStraight Crosscut Clamp Left Side Rightside Indicator Point Scale MountingbracketTo Bevel CUT with Your Miter SAW Bevel CUTCompound Miter CUT Bevelcut Fence Screw ClampTo Make a Compound CUT with Your Miter SAW Compound Mitercut LampLongworkpiece Workpiecesupports Support Long Workpieces45x 45COMPOUNDMITERCUT 45.00 44.89 29.91 25.63 44.56 35.58 22.19 COMPOUND-ANGLE Settings for Popular StructuresPitch 14.51 10.65 17.37 44.14 35.37 22.14 17.72 17.93 00 MCutting Crown Molding Laying Molding Flat on Miter TableCutting Warped Material Bevel Angle Type of Cut Setting Left side, inside cornerWrong Clamping Wide WorkpiecesExtension Cords GeneralLubrication Partmay create a hazard or cause product damageFigureA Craftsman Compound Miter SAW Model NumberKEY Part NO. Number Craftsman Compound Miter SAW- Model NumberDescription Quan FigureB KEY Part Number Description Quan Figure C Parts List for Figure C Figure D Parts List for Figure D Get it fixed, at your home or ourst

315.21213 specifications

The Craftsman 315.21213 is a versatile and reliable tool designed for both professional tradespeople and DIY enthusiasts. This compact and powerful rotary tool is known for its impressive performance and a wide array of features that make it essential for a variety of tasks.

One of the main features of the Craftsman 315.21213 is its powerful motor, which provides robust performance capable of handling different materials including wood, metal, and plastic. This rotary tool boasts a variable speed control that allows users to adjust the RPM according to their specific needs, ranging from delicate tasks like engraving at lower speeds to more demanding applications such as grinding or cutting at higher speeds.

The 315.21213 is compatible with a vast selection of accessories, enabling it to effortlessly switch between tasks. With its easy-to-use chuck system, users can quickly swap out bits and attachments without the need for additional tools, ensuring that workflow remains efficient and uninterrupted. The adaptability of this rotary tool makes it a favored choice for intricate projects like jewelry making, model building, and home improvement tasks.

In terms of technology, the Craftsman 315.21213 incorporates a lightweight design that enhances its portability. Weighing just enough to allow for extended use without causing fatigue, this tool is also designed with user comfort in mind, featuring an ergonomic grip that provides a secure hold even during prolonged projects.

Safety is another key characteristic of the Craftsman 315.21213. The tool is equipped with an integrated safety switch that prevents accidental starts, providing peace of mind when handling various tasks. Additionally, its ventilation system helps manage heat during prolonged use, protecting the motor from overheating and improving overall durability.

The Craftsman 315.21213 stands out for its reliable performance and exceptional versatility. Whether you are tackling a small craft project or larger renovation tasks, this rotary tool delivers the quality and consistency needed to achieve professional results. With a combination of power, adaptability, and user-friendly features, the Craftsman 315.21213 is a top choice for those seeking a reliable and efficient rotary tool.
Top Page Image Contents