3 When you’ve finished making the settings, press
ENTER.
MultEQ XT: Auto Setup
| AUDYSSEY |
Speakers Type(Front) | Normal |
Powered Zone 2 | No |
Powered Zone 3 | No |
Subwoofer | Yes |
Perform the “Speaker Setup” according to your speaker configuration:
–Speakers Type(Front) (➔ page 47)
–Powered Zone 2 (➔ page 47)
–Powered Zone 3 (➔ page 47)
–Subwoofer (➔ page 48)
If you use a powered subwoofer(s), go to step 4. If not, go to step 5.
When an optional unit is connected to the UNIVERSAL PORT jack on the AV receiver, the optional unit setting may appear on the speaker setting menu.
4 Adjust the subwoofer volume level to 75 dB, and then press ENTER.
Test tones are played through the subwoofer. Use the volume control on the subwoofer.
Note
•If your subwoofer does not have a volume control, disregard the displayed level and press ENTER to proceed to the next step.
•If you set the subwoofer’s volume control to its maximum and the level displayed is lower than 75 dB, leave the subwoofer’s volume control at its maximum and press ENTER to proceed to the next step.
5 Use q/wto select “Audyssey Quick Start” or “Audyssey MultEQ XT Full Calibration”.
6 Press ENTER.
Audyssey MultEQ® XT Room Correction and Speaker Setup starts.
Test tones are played through each speaker as Audyssey MultEQ XT Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey MultEQ XT Room Correction and Speaker Setup, unless you want to cancel the setup. If you select “Audyssey Quick Start”, you will go to step 9.
7 Place the setup microphone at the next position, and then press ENTER.
Audyssey MultEQ XT performs more measurements. This takes a few minutes.
8 When prompted, repeat step 7.
9 Use q/wto select an option, and then press
ENTER.
MultEQ XT: Auto Setup |
|
|
|
| AUDYSSEY |
Subwoofer | : | Yes |
Front | : | 100Hz |
Center | : | 40Hz |
Surround | : | 100Hz |
Front Wide | : | None |
Front High | : | None |
Surround Back | : | 120Hz |
Surround Back Ch | : | 2ch |
Save |
|
|
Cancel |
|
|
The options are:
`Save:
Save the calculated settings and exit
Audyssey MultEQ XT Room Correction and
Speaker Setup.
`Cancel:
Cancel Audyssey MultEQ XT Room Correction
and Speaker Setup.
Tip
•You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by using e/r.
10 Use q/wto select a target, and use e/rto change the setting.
After the results of Audyssey MultEQ XT have been saved, the menu will display the “Audyssey”
(➔ page 53), “Dynamic EQ” (➔ page 53), “Dynamic Volume” (➔ page 53) settings.
Note
•When “Audyssey Quick Start” has been used for measurement, “Audyssey” cannot be selected.
•These settings are applied to all input selectors.
11 Press ENTER.
12 Disconnect the speaker setup microphone.
Note
•You can cancel Audyssey MultEQ XT Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.
•Do not connect or disconnect any speakers during Audyssey MultEQ XT Room Correction and Speaker Setup.
•If the AV receiver is muted, it will be unmuted automatically when Audyssey MultEQ XT Room Correction and Speaker Setup starts.
•Changes to the room after Audyssey MultEQ XT Room Correction and Speaker Setup requires you run Audyssey MultEQ XT Room Correction and Speaker Setup again, as room EQ characteristics may have changed.
En
32
