Onkyo TX-NR1009 Video, Tuner, Remote Controller, The on-screenmenus don’t appear

With some CD and LD players, you won’t be able to — playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate,

or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.

Playing DTS program material, using the pause, fast — forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.

If the message “Resolution Error” appears on the — AV receiver’s display, this indicates that your TV does not support the current video resolution and

you need to select another resolution on your DVD player.

■The on-screen menus don’t appear

On your TV, make sure that the video input to which — the AV receiver is connected is selected.

When the AV receiver is not connected to a TV via — HDMI, onscreen menus are not displayed.

■The beginning of audio received by an HDMI IN can’t be heard

Since it takes longer to identify the format of an	—
HDMI signal than it does for other digital audio
signals, audio output may not start immediately.

■The on screen display does not appear

Depending on the input signal, the on screen display 59 may not appear when the input signal from the

HDMI IN is output to a device connected to the

HDMI OUT MAIN.

■There’s no sound during Whole House Mode

Make sure you’ve selected an analog audio input. 47

Video

■ There’s no picture

Make sure that all video connecting plugs are pushed	16
in all the way.
Make sure that each video component is properly	17, 18
connected.
If your TV is connected to the HDMI output(s),	46
select “- - - - -” in the “HDMI Input” setup to watch
composite video, S-Video and component video
sources.
If the video source is connected to a component	18, 46
video input, you must assign that input to an input
selector, and your TV must be connected to either
the HDMI output(s) or COMPONENT VIDEO
MONITOR OUT.
If the video source is connected to a composite video	18
input, your TV must be connected to the HDMI
output(s) or the corresponding composite video
output.
If the video source is connected to an HDMI input,	17, 46
you must assign that input to an input selector, and
your TV must be connected to the HDMI output(s).

While the Pure Audio listening mode is selected, the — video circuitry is turned off and only video signals input through HDMI IN can be output.

On your TV, make sure that the video input to which — the AV receiver is connected is selected.

If the “Monitor Out” setting is set to “Both(Main)” — or “Both(Sub)” while your TV is connected to a secondary HDMI output (not a primary HDMI output), the picture may not appear. In this case, change the setting to “Both”.

■There’s no picture from a source connected to an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is	93
not guaranteed. In addition, video signals from a PC
are not guaranteed.
When the resolution is set to any resolution not	46
supported by the TV, no video is output from the
HDMI outputs.

Tuner

■Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light

Relocate your antenna.	—
Move the AV receiver away from your TV or	—
computer.
Listen to the station in mono.	28
When listening to an AM station, operating the	—
remote controller may cause noise.
Passing cars and airplanes can cause interference.	—
Concrete walls weaken radio signals.	—

If nothing improves the reception, install an outdoor — antenna.

Remote Controller

■ The remote controller doesn’t work

Before operating this unit, be sure to press	—
RECEIVER.
Make sure that the batteries are installed with the	4
correct polarity.
Install new batteries. Don’t mix different types of	4
batteries, or old and new batteries.
Make sure that the remote controller is not too far	4
away from the AV receiver, and that there’s no
obstruction between the remote controller and the
AV receiver’s remote control sensor.
Make sure that the AV receiver is not subjected to	—
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
If the AV receiver is installed in a rack or cabinet	—
with colored-glass doors, the remote controller may
not work reliably when the doors are closed.
Make sure you’ve selected the correct remote	11, 75
controller mode.
When using the remote controller to control other	—
manufacturers’ AV components, some buttons may
not work as expected.
Make sure you’ve entered the correct remote control	74
code.
Make sure to set the same ID on both the AV	59
receiver and remote controller.

En

81