Music Server and Internet Radio
■Can’t access the server or Internet radio
Check the network connection between the AV | — |
receiver and your router or switch. |
|
|
|
Make sure that your modem and router are properly | — |
connected, and make sure they are both turned on. |
|
Make sure the server is up and running and | 94, 96 |
compatible with the AV receiver. |
|
|
|
Check the “Network” settings. | 62 |
|
|
■Playback stops while listening to music files on the server
Make sure your server is compatible with the AV | 94, 96 |
receiver. |
|
|
|
If you download or copy large files on your | — |
computer, playback may be interrupted. Try closing |
|
any unused programs, use a more powerful |
|
computer, or use a dedicated server. |
|
If the server is serving large music files to several | — |
networked devices simultaneously, the network may |
|
become overloaded and playback may be |
|
interrupted. Reduce the number of playback devices |
|
on the network, upgrade your network, or use a |
|
switch instead of a hub. |
|
■Can’t connect to the AV receiver from a Web browser
If you’re using DHCP, your router may not always | 62 |
allocate the same IP address to the AV receiver, so if |
|
you find that you can’t connect to a server or Internet |
|
radio station, recheck the AV receiver’s IP address |
|
on the “Network” screen. |
|
|
|
Check the “Network” settings. | 62 |
|
|
■The sound changes when I connect my headphones
When a pair of headphones is connected, the | — |
listening mode is set to Stereo, unless it’s already set |
|
to Stereo, Mono, Direct, or Pure Audio. |
|
■The speaker distance cannot be set as required
In some cases, corrected values suitable for home | — |
theater use may be set automatically. |
|
■ The display doesn’t work
The display is turned off when the Pure Audio | — |
listening mode is selected. |
|
■How do I change the language of a multiplex source
Use the “Multiplex” setting on the “Audio Adjust” 51 menu to select “Main” or “Sub”.
■ The ufunctions don’t work
To use u, you must make an uconnection and | 20 |
an analog audio connection (RCA) between the |
|
component and AV receiver, even if they are |
|
connected digitally. |
|
|
|
While Zone 2 or Zone 3 is selected, the u | 20 |
functions don’t work. |
|
|
|
■The functions System On/Auto Power On and Direct Change don’t work for components connected via u
While Zone 2 or Zone 3 is selected, the u | 20 |
functions don’t work. |
|
USB Device Playback
■Can’t access the music files on a USB device
Make sure the USB device is plugged in properly. —
The AV receiver supports USB devices that support — the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class.
USB memory devices with security functions cannot — be played.
Others
■Standby power consumption
In the following cases, the power consumption in | 18, 60, |
standby mode may reach up to a maximum of 75 W: 62
–You are using the Universal Port jack.
–“Network Control” is set to “Enable” in the “Network” setting.
–“HDMI Control(RIHD)” setting is set to “On”. (Depending on the TV status, the AV receiver will enter standby mode as usual.)
–The “HDMI Through” setting is set to other than “Off”.
■When performing “Automatic Speaker Setup”, the measurement fails showing the message “Ambient noise is too high.”
This can be caused by a malfunction in your speaker — unit. Check if the unit produces normal sounds.
■The following settings can be made for the
You must use the buttons on the unit to make these settings.
On the AV receiver, press the input selector for the input source that you want to set and the SETUP button simultaneously. While holding down the input selector button, press SETUP until “Video ATT:On” appears on the display. Then, release both buttons. To reactivate the setting, repeat the above process so that “Video ATT:Off” appears on the display, and release the buttons.
• Video Attenuation
This setting can be made for the BD/DVD, VCR/DVR, CBL/SAT, GAME or AUX input.
If you have a game console connected to the composite video input, and the picture isn’t very clear, you can attenuate the gain.
Video ATT:Off: (default).
Video ATT:On: Gain is reduced by 2 dB.
En
83
