Weed Eater WE16542E manual Before Starting the Engine, To Operate on Hills, To Transport

Page 12

OPERATION

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 17/32 washer, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE WHEEL

MOUNTING

BRACKET

3/8-16

LOCKNUT

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

17/32 WASHER

 

FIG. 6

TO OPERATE MOWER (See Fig. 7)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT LIFT

LEVER HIGH POSITION

ATTACHMENT CLUTCH LEVER

"DISENGAGED"

POSITION

LOW POSITION

DEFLECTOR

SHIELD

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

•To change engine oil, see the Customer Responsibilities section in this manual.

FIG. 7

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model NO. WE16542E Safety Rules IV. ServiceGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKeys Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Throttle Control see FIGBefore Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig ¿ Lubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE16542EElectrical 2122178437 178861Chassis and Enclosures 174620 17490608Drive 175765 175456175578 179114Steering Assembly 175121 177876175146 175118Optional Equipment Spark Arrester170551 Control Throt/Ch Lh Seat Assembly Decals Wheels & Tires180530 180531Mower Lift 175689 Mower Deck 143 159 144 150174493 173984178342 179292Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation

WE16542E specifications

The Weed Eater WE16542E is a versatile and powerful string trimmer designed to tackle a range of landscaping tasks with ease. Boasting a robust 16-inch cutting width, this trimmer is ideal for homeowners and gardeners who need a reliable tool for maintaining their lawns and gardens. The WE16542E stands out in the crowded market of outdoor power equipment due to its combination of features, durability, and user-friendly design.

One of the key characteristics of the WE16542E is its lightweight construction. Weighing in at just under 10 pounds, this trimmer minimizes fatigue during extended use, allowing users to maneuver effortlessly around their yards. Its ergonomic handle is designed for comfort, providing a secure grip and reducing strain on the hands and wrists, an essential feature for those who spend long hours working on their property.

The WE16542E is powered by a robust 42cc 2-cycle engine. This engine not only delivers ample power for cutting through thick grass and weeds but also offers an efficient performance that ensures minimal emissions. The trimmer features an easy starting system, simplifying the process of getting to work quickly without the frustration often associated with traditional pull-start engines.

Equipped with a dual-line cutting head, the WE16542E allows users to load two lines simultaneously, enhancing its efficiency and reducing the time spent trimming. The automatic line feed system ensures that the cutting lines are replenished as needed, promoting continuous operation without the hassle of manual adjustments. This feature is particularly advantageous for tackling large areas or dense vegetation.

For added versatility, the WE16542E is compatible with a range of attachments, making it a multi-functional tool capable of performing various tasks such as edging, pruning, and even cultivating soil. This adaptability makes it an excellent investment for those looking to simplify their gardening and landscaping efforts.

In terms of build quality, the WE16542E is designed to withstand the rigors of regular use. Its durable materials and construction ensure longevity, making it a reliable choice for homeowners. Coupled with its user-friendly features, the Weed Eater WE16542E is a powerful and efficient string trimmer that simplifies yard maintenance, making it an essential tool for any gardening enthusiast.
Top Page Image Contents