Weed Eater WE16542E To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse, Engine

Page 23

SERVICE AND ADJUSTMENTS

KEPS

NUT

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 27

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 28

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 29)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

 

GOVERNOR

GOVERNOR

 

CONTROL

 

CONTROL LEVER

 

PLATE

 

 

HOLES “A”

CLAMP

THROTTLE

 

SCREW

CABLE

 

 

FIG. 29

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. WE16542E II. Slope Operation Safety RulesIV. Service General OperationTable of Contents Customer Responsibilities Product SpecificationsKeys Unassembled PartsSteering Wheel Seat Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control see FIG HOW to USE Your TractorTowing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To TransportTo Start Engine See Fig Mowing TipsADD Gasoline Before Each USE ¿ Lubrication ChartCustomer Responsibilities General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenTo Service PRE-CLEANER To Service CartridgeIN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE16542E Schematic2122 Electrical178861 178437Chassis and Enclosures 17490608 174620Drive 179114 175765175456 175578Steering Assembly 175118 175121177876 175146Spark Arrester Optional Equipment170551 Control Throt/Ch Lh Seat Assembly 180531 DecalsWheels & Tires 180530Mower Lift 175689 143 159 144 150 Mower Deck179292 174493173984 178342Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation

WE16542E specifications

The Weed Eater WE16542E is a versatile and powerful string trimmer designed to tackle a range of landscaping tasks with ease. Boasting a robust 16-inch cutting width, this trimmer is ideal for homeowners and gardeners who need a reliable tool for maintaining their lawns and gardens. The WE16542E stands out in the crowded market of outdoor power equipment due to its combination of features, durability, and user-friendly design.

One of the key characteristics of the WE16542E is its lightweight construction. Weighing in at just under 10 pounds, this trimmer minimizes fatigue during extended use, allowing users to maneuver effortlessly around their yards. Its ergonomic handle is designed for comfort, providing a secure grip and reducing strain on the hands and wrists, an essential feature for those who spend long hours working on their property.

The WE16542E is powered by a robust 42cc 2-cycle engine. This engine not only delivers ample power for cutting through thick grass and weeds but also offers an efficient performance that ensures minimal emissions. The trimmer features an easy starting system, simplifying the process of getting to work quickly without the frustration often associated with traditional pull-start engines.

Equipped with a dual-line cutting head, the WE16542E allows users to load two lines simultaneously, enhancing its efficiency and reducing the time spent trimming. The automatic line feed system ensures that the cutting lines are replenished as needed, promoting continuous operation without the hassle of manual adjustments. This feature is particularly advantageous for tackling large areas or dense vegetation.

For added versatility, the WE16542E is compatible with a range of attachments, making it a multi-functional tool capable of performing various tasks such as edging, pruning, and even cultivating soil. This adaptability makes it an excellent investment for those looking to simplify their gardening and landscaping efforts.

In terms of build quality, the WE16542E is designed to withstand the rigors of regular use. Its durable materials and construction ensure longevity, making it a reliable choice for homeowners. Coupled with its user-friendly features, the Weed Eater WE16542E is a powerful and efficient string trimmer that simplifies yard maintenance, making it an essential tool for any gardening enthusiast.
Top Page Image Contents