Weed Eater WE16542E manual To Remove Wheel for Repairs See Fig, Replacing Battery See Figs

Page 22

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL FOR REPAIRS (See Fig. 24)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

 

FIG. 24

TO START ENGINE WITH A WEAK BATTERY (See Fig. 25)

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Customer Responsibili- ties section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

POSITIVE TERMINAL

 

NEGATIVE TERMINAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CHASSIS

 

 

CABLES

POSITIVE

NEGATIVE

TERMINAL

TERMINAL

CHARGED

 

 

BATTERY

FIG. 25

REPLACING BATTERY (See Figs. 26 and 27)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acciden- tal grounding.

•Lift seat pan to raised position and open battery box door.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

•Close battery box door.

SEAT PAN

BATTERY

BOX DOOR

FIG. 26

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model NO. WE16542E General Operation Safety RulesIV. Service II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesSteering Wheel Seat Unassembled PartsKeys To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Throttle Control see FIGTo Transport Before Starting the EngineTo Operate on Hills Towing Carts and Other ATTACH- MentsADD Gasoline Mowing TipsTo Start Engine See Fig General Recommendations ¿ Lubrication ChartCustomer Responsibilities Before Each USETires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingTo Service Cartridge Clean AIR ScreenTo Service PRE-CLEANER Engine Cooling Fins See FigSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE16542EElectrical 2122178437 178861Chassis and Enclosures 174620 17490608Drive 175578 175765175456 179114Steering Assembly 175146 175121177876 175118Optional Equipment Spark Arrester170551 Control Throt/Ch Lh Seat Assembly 180530 DecalsWheels & Tires 180531Mower Lift 175689 Mower Deck 143 159 144 150178342 174493173984 179292Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation

WE16542E specifications

The Weed Eater WE16542E is a versatile and powerful string trimmer designed to tackle a range of landscaping tasks with ease. Boasting a robust 16-inch cutting width, this trimmer is ideal for homeowners and gardeners who need a reliable tool for maintaining their lawns and gardens. The WE16542E stands out in the crowded market of outdoor power equipment due to its combination of features, durability, and user-friendly design.

One of the key characteristics of the WE16542E is its lightweight construction. Weighing in at just under 10 pounds, this trimmer minimizes fatigue during extended use, allowing users to maneuver effortlessly around their yards. Its ergonomic handle is designed for comfort, providing a secure grip and reducing strain on the hands and wrists, an essential feature for those who spend long hours working on their property.

The WE16542E is powered by a robust 42cc 2-cycle engine. This engine not only delivers ample power for cutting through thick grass and weeds but also offers an efficient performance that ensures minimal emissions. The trimmer features an easy starting system, simplifying the process of getting to work quickly without the frustration often associated with traditional pull-start engines.

Equipped with a dual-line cutting head, the WE16542E allows users to load two lines simultaneously, enhancing its efficiency and reducing the time spent trimming. The automatic line feed system ensures that the cutting lines are replenished as needed, promoting continuous operation without the hassle of manual adjustments. This feature is particularly advantageous for tackling large areas or dense vegetation.

For added versatility, the WE16542E is compatible with a range of attachments, making it a multi-functional tool capable of performing various tasks such as edging, pruning, and even cultivating soil. This adaptability makes it an excellent investment for those looking to simplify their gardening and landscaping efforts.

In terms of build quality, the WE16542E is designed to withstand the rigors of regular use. Its durable materials and construction ensure longevity, making it a reliable choice for homeowners. Coupled with its user-friendly features, the Weed Eater WE16542E is a powerful and efficient string trimmer that simplifies yard maintenance, making it an essential tool for any gardening enthusiast.
Top Page Image Contents