Weed Eater WE16542E manual To Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO ADJUST BRAKE (See Fig. 21)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-1/2", loosen jam nut and turn nut “A” until distance becomes 1-1/2". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE "ENGAGED"

1-1/2"

NUT "A"

JAM NUT

OPERATING

ARM

FIG. 21

TO REPLACE MOTION DRIVE BELT (See Fig. 22)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

•Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

•Remove belt from stationary idler and clutching idler.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Pull belt toward front of tractor and remove downwards from around engine pulley.

•Install new belt by reversing above procedure.

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSAXLE

PULLEY

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 23)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT LEVER

NEUTRAL

LOCK GATE

ADJUSTMENT

BOLT

FIG. 23

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

FIG. 22

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. WE16542E IV. Service Safety RulesGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsUnassembled Parts Steering Wheel SeatKeys Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To USE Throttle Control see FIG HOW to USE Your TractorTo Operate on Hills Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig Customer Responsibilities ¿ Lubrication ChartGeneral Recommendations Before Each USEBrake Operation TractorTires Operator Presence SystemEngine BatteryBelts Transaxle CoolingTo Service PRE-CLEANER Clean AIR ScreenTo Service Cartridge Engine Cooling Fins See FigMuffler CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Brake See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Replace Headlight Bulb To Adjust CarburetorInterlocks and Relays To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number WE16542E Schematic2122 Electrical178861 178437Chassis and Enclosures 17490608 174620Drive 175456 175765175578 179114Steering Assembly 177876 175121175146 175118Spark Arrester Optional Equipment170551 Control Throt/Ch Lh Seat Assembly Wheels & Tires Decals180530 180531Mower Lift 175689 143 159 144 150 Mower Deck173984 174493178342 179292Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation

WE16542E specifications

The Weed Eater WE16542E is a versatile and powerful string trimmer designed to tackle a range of landscaping tasks with ease. Boasting a robust 16-inch cutting width, this trimmer is ideal for homeowners and gardeners who need a reliable tool for maintaining their lawns and gardens. The WE16542E stands out in the crowded market of outdoor power equipment due to its combination of features, durability, and user-friendly design.

One of the key characteristics of the WE16542E is its lightweight construction. Weighing in at just under 10 pounds, this trimmer minimizes fatigue during extended use, allowing users to maneuver effortlessly around their yards. Its ergonomic handle is designed for comfort, providing a secure grip and reducing strain on the hands and wrists, an essential feature for those who spend long hours working on their property.

The WE16542E is powered by a robust 42cc 2-cycle engine. This engine not only delivers ample power for cutting through thick grass and weeds but also offers an efficient performance that ensures minimal emissions. The trimmer features an easy starting system, simplifying the process of getting to work quickly without the frustration often associated with traditional pull-start engines.

Equipped with a dual-line cutting head, the WE16542E allows users to load two lines simultaneously, enhancing its efficiency and reducing the time spent trimming. The automatic line feed system ensures that the cutting lines are replenished as needed, promoting continuous operation without the hassle of manual adjustments. This feature is particularly advantageous for tackling large areas or dense vegetation.

For added versatility, the WE16542E is compatible with a range of attachments, making it a multi-functional tool capable of performing various tasks such as edging, pruning, and even cultivating soil. This adaptability makes it an excellent investment for those looking to simplify their gardening and landscaping efforts.

In terms of build quality, the WE16542E is designed to withstand the rigors of regular use. Its durable materials and construction ensure longevity, making it a reliable choice for homeowners. Coupled with its user-friendly features, the Weed Eater WE16542E is a powerful and efficient string trimmer that simplifies yard maintenance, making it an essential tool for any gardening enthusiast.
Top Page Image Contents