Weed Eater 186843 manual HOW to USE Your Tractor

Page 11

OPERATION

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig. 5)

Your tractor is equipped with an operator presence sens- ing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

Depress clutch/brake pedal into full “BRAKE” position and hold.

Place parking brake lever in “ENGAGED” position and release pressure from clutch/brake pedal. Pedal should remain in “BRAKE” position. Make sure parking brake will hold tractor secure.

 

ATTACHMENT CLUTCH

 

LEVER "ENGAGED"

 

POSITION

THROTTLE/

IGNITION KEY

 

CHOKE

"DISENGAGED"

CONTROL

LEVER

POSITION

 

PARKING BRAKE

"BRAKE"

"ENGAGED"

POSITION

POSITION

 

GEAR SHIFT

CLUTCH/BRAKE

LEVER

PARKING BRAKE

PEDAL "DRIVE"

"DISENGAGED"

POSITION

POSITION

 

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, al- ways stop engine when stopping tractor on grass areas.

CAUTION: Always stop tractor com- pletely,as described above,before leav- ing the operator's position; to empty grass catcher, etc.

TO USE THROTTLE CONTROL (See Fig. 5)

Always operate engine at full throttle.

Operating engine at less than full throttle reduces the battery charging rate.

Full throttle offers the best bagging and mower perfor- mance.

TO MOVE FORWARD AND BACKWARD (See Fig. 5)

The direction and speed of movement is controlled by the gearshift lever.

Start tractor with clutch/brake pedal depressed and gearshift lever in neutral (N) position.

Move gearshift lever to desired position.

Slowly release clutch/brake pedal to start move- ment.

IMPORTANT: BRING TRACTOR TO A COMPLETE STOP BEFORE SHIFTING OR CHANGING GEARS. FAILURE TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR TRANSAXLE.

FIG. 5

STOPPING (See Fig. 5)

MOWER BLADES -

To stop mower blades,move attachment clutch lever to “DISENGAGED” position.

GROUND DRIVE -

To stop ground drive, depress clutch/brake pedal into full “BRAKE” position.

Move gearshift lever to neutral (N) position.

ENGINE -

Move throttle control to slow position.

NOTE: Failure to move throttle control to slow position and allowing engine to idle before stopping may cause engine to “backfire”.

Turn ignition key to “OFF” position and remove key. Always remove key when leaving tractor to prevent unauthorized use.

Never use choke to stop engine.

IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD).

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 5)

The position of the attachment lift lever determines the cutting height.

Grasp lift lever.

Press plunger with thumb and move lever to desired position.

The cutting height range is approximately 1-1/2 to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

11

Image 11
Contents Model NO. WET1742STA Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine IN-LINE Fuel Filter See Fig CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Replace Fuse To Replace Headlight BulbInterlocks and Relays To Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WET1742STA SchematicElectrical KEY Part Description Chassis and Enclosures 5479J Plug Btn Blk Drive Bolt Hex 7/16-20 x 4 x Gr -1.5 Thr Steering Assembly Nut Hex Jam Toplock 1/2-20 Unf Engine 170551 Control Throt /Ch Flag Seat Assembly Wheels & Tires DecalsMower Lift 159460 Mower Deck Mandrel Assembly Includes Hous Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation