Weed Eater 195383 Reverse Operation System ROS, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

•Depress clutch/brake pedal all the way down and hold.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before backing.

•Move gear shift lever to reverse (R) position and slowly release clutch/brake pedal to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

02828

TO OPERATE MOWER (See Fig. 6)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT

LIFT LEVER

HIGH POSITION

LOW

POSITION

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

DEFLECTOR

SHIELD

FIG. 6

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents HD13538 Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Battery EngineBelts Transaxle CoolingCleaning Clean AIR ScreenAIR Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195383 specifications

The Weed Eater 195383 is a standout model in the world of outdoor gardening tools, designed to provide efficient and effective grass trimming and edging solutions. This versatile tool is particularly popular among homeowners and landscaping professionals alike, thanks to its blend of functionality, ease of use, and innovative features.

One of the defining characteristics of the Weed Eater 195383 is its lightweight design. Weighing in at just a few pounds, it allows for easy maneuverability, making it perfect for tackling those tricky spots around flower beds, trees, and fences. The tool's ergonomic handle significantly enhances comfort during extended use, reducing strain on the hands and arms while you work.

The Weed Eater 195383 sports a powerful electric motor, which delivers consistent performance without the hassle of mixing fuel or dealing with exhaust fumes. This eco-friendly feature appeals to environmentally conscious users, minimizing carbon footprint while ensuring a clean working environment. With its quiet operation, you can also operate it in residential areas without disturbing your neighbors.

This model is equipped with a patented automatic feed spool system that releases the cutting line as needed. This means you won’t need to stop and manually adjust the line, allowing for uninterrupted work. The dual-line cutting system enhances trimming efficiency, cutting a broader swath of grass with each pass, which saves time and effort.

In terms of technology, the Weed Eater 195383 features a robust cutting head that can handle various types of grass and vegetation. It offers adjustable cutting lengths, letting users customize their trimming height based on specific yard needs. The head is designed for easy replacement of the cutting line, a process that even novice users can perform without hassle.

Ultimately, the Weed Eater 195383 combines user-friendly features with powerful performance, making it an essential tool for maintaining a neat and tidy yard. Whether you’re a casual gardener or a dedicated landscaper, this model is engineered to meet your trimming needs efficiently, transforming your outdoor space into a well-manicured oasis. With its reliability and thoughtful design, the Weed Eater 195383 is poised to become your go-to garden companion.
Top Page Image Contents