Weed Eater 195383 manual Tractor, Blade Removal See Fig, To Sharpen Blade See Fig

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

828

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEATTREATED.IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS.

 

 

MANDREL

TRAILING

BLADE

ASSEMBLY

EDGE UP

 

 

CENTER

 

 

 

 

HOLE

FLAT WASHER

 

 

LOCK WASHER

 

STAR

BLADE BOLT

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents HD13538 Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Battery EngineBelts Transaxle CoolingCleaning Clean AIR ScreenAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195383 specifications

The Weed Eater 195383 is a standout model in the world of outdoor gardening tools, designed to provide efficient and effective grass trimming and edging solutions. This versatile tool is particularly popular among homeowners and landscaping professionals alike, thanks to its blend of functionality, ease of use, and innovative features.

One of the defining characteristics of the Weed Eater 195383 is its lightweight design. Weighing in at just a few pounds, it allows for easy maneuverability, making it perfect for tackling those tricky spots around flower beds, trees, and fences. The tool's ergonomic handle significantly enhances comfort during extended use, reducing strain on the hands and arms while you work.

The Weed Eater 195383 sports a powerful electric motor, which delivers consistent performance without the hassle of mixing fuel or dealing with exhaust fumes. This eco-friendly feature appeals to environmentally conscious users, minimizing carbon footprint while ensuring a clean working environment. With its quiet operation, you can also operate it in residential areas without disturbing your neighbors.

This model is equipped with a patented automatic feed spool system that releases the cutting line as needed. This means you won’t need to stop and manually adjust the line, allowing for uninterrupted work. The dual-line cutting system enhances trimming efficiency, cutting a broader swath of grass with each pass, which saves time and effort.

In terms of technology, the Weed Eater 195383 features a robust cutting head that can handle various types of grass and vegetation. It offers adjustable cutting lengths, letting users customize their trimming height based on specific yard needs. The head is designed for easy replacement of the cutting line, a process that even novice users can perform without hassle.

Ultimately, the Weed Eater 195383 combines user-friendly features with powerful performance, making it an essential tool for maintaining a neat and tidy yard. Whether you’re a casual gardener or a dedicated landscaper, this model is engineered to meet your trimming needs efficiently, transforming your outdoor space into a well-manicured oasis. With its reliability and thoughtful design, the Weed Eater 195383 is poised to become your go-to garden companion.
Top Page Image Contents