Weed Eater 195383 manual Troubleshooting Points, Problem Cause Correction

Page 25

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

 

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

4.

Bad spark plug.

4.

Replace spark plug.

 

5.

Dirty air filter.

5.

Clean/replace air filter.

 

6.

Dirty fuel filter.

6.

Replace fuel filter.

 

7.

Water in fuel.

7.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

8.

Loose or damaged wiring.

8.

Check all wiring.

 

9.

Carburetor out of adjustment.

9.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

10.

Engine valves out of adjustment.

10.

Contact an authorized service center/department.

 

 

 

 

 

 

Hard to start

1.

Dirty air filter.

1.

Clean/replace air filter.

 

2.

Bad spark plug.

2.

Replace spark plug.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Dirty fuel filter.

4.

Replace fuel filter.

 

5.

Stale or dirty fuel.

5.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Carburetor out of adjustment.

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

8.

Engine valves out of adjustment.

8.

Contact an authorized service center/department.

 

 

 

 

 

 

Engine will not turn over

1.

Clutch/brake pedal not depressed.

1.

Depress clutch/brake pedal.

 

2.

Attachment clutch is engaged.

2.

Disengage attachment clutch.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Blown fuse.

4.

Replace fuse.

 

5.

Corroded battery terminals.

5.

Clean battery terminals.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Faulty ignition switch.

7.

Check/replace ignition switch.

 

8.

Faulty solenoid or starter.

8.

Check/replace solenoid or starter.

 

9.

Faulty operator presence switch(es).

9.

Contact an authorized service center/department.

 

 

 

 

 

 

Engine clicks but will not

1.

Weak or dead battery.

1.

Recharge or replace battery.

start

2.

Corroded battery terminals.

2.

Clean battery terminals.

 

3.

Loose or damaged wiring.

3.

Check all wiring.

 

4.

Faulty solenoid or starter.

4.

Check/replace solenoid or starter.

 

 

 

 

 

 

Loss of power

1.

Cutting too much grass/too fast.

1.

Raise cutting height/reduce speed.

 

2.

Throttle in “CHOKE” position.

2.

Adjust throttle control.

 

3.

Build-up of grass, leaves and trash under mower.

3.

Clean underside of mower housing.

 

4.

Dirty air filter.

4.

Clean/replace air filter.

 

5.

Low oil level/dirty oil.

5.

Check oil level/change oil.

 

6.

Faulty spark plug.

6.

Clean and regap or change spark plug.

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

8.

Stale or dirty fuel.

8.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

9.

Water in fuel.

9.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

10.

Spark plug wire loose.

10.

Connect and tighten spark plug wire.

 

11.

Dirty engine air screen/fins.

11.

Clean engine air screen/fins.

 

12.

Dirty/clogged muffler.

12.

Clean/replace muffler.

 

13.

Loose or damaged wiring.

13.

Check all wiring.

 

14.

Carburetor out of adjustment.

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

15.

Engine valves out of adjustment.

15.

Contact an authorized service center/department.

 

 

 

 

 

 

Excessive vibration

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Bent blade mandrel.

2.

Replace blade mandrel.

 

3.

Loose/damaged part(s).

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

 

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Always Wear EYE Protection During Operation HD13538Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills To TransportCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine BatteryBelts Transaxle CoolingClean AIR Screen CleaningAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

195383 specifications

The Weed Eater 195383 is a standout model in the world of outdoor gardening tools, designed to provide efficient and effective grass trimming and edging solutions. This versatile tool is particularly popular among homeowners and landscaping professionals alike, thanks to its blend of functionality, ease of use, and innovative features.

One of the defining characteristics of the Weed Eater 195383 is its lightweight design. Weighing in at just a few pounds, it allows for easy maneuverability, making it perfect for tackling those tricky spots around flower beds, trees, and fences. The tool's ergonomic handle significantly enhances comfort during extended use, reducing strain on the hands and arms while you work.

The Weed Eater 195383 sports a powerful electric motor, which delivers consistent performance without the hassle of mixing fuel or dealing with exhaust fumes. This eco-friendly feature appeals to environmentally conscious users, minimizing carbon footprint while ensuring a clean working environment. With its quiet operation, you can also operate it in residential areas without disturbing your neighbors.

This model is equipped with a patented automatic feed spool system that releases the cutting line as needed. This means you won’t need to stop and manually adjust the line, allowing for uninterrupted work. The dual-line cutting system enhances trimming efficiency, cutting a broader swath of grass with each pass, which saves time and effort.

In terms of technology, the Weed Eater 195383 features a robust cutting head that can handle various types of grass and vegetation. It offers adjustable cutting lengths, letting users customize their trimming height based on specific yard needs. The head is designed for easy replacement of the cutting line, a process that even novice users can perform without hassle.

Ultimately, the Weed Eater 195383 combines user-friendly features with powerful performance, making it an essential tool for maintaining a neat and tidy yard. Whether you’re a casual gardener or a dedicated landscaper, this model is engineered to meet your trimming needs efficiently, transforming your outdoor space into a well-manicured oasis. With its reliability and thoughtful design, the Weed Eater 195383 is poised to become your go-to garden companion.
Top Page Image Contents