Weed Eater 195383 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place gearshift lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 13)

Mower will be easier to remove from the right side of trac- tor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and remove clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 13)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with deflector shield to right side of tractor.

•Lower lift lever to its lowest position.

•Connect front links to mower deck and secure with retainer springs..

•Connect suspension arms to rear deck brackets and secure with retainer springs.

•Connect anti-swaybar to chassis bracket and secure with retainer spring.

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Install belt onto engine pulley.

 

SMALL

 

 

RETAINER

 

 

SPRING

 

FLAT WASHER

SUSPENSION

 

 

 

CLUTCH SPRING

ARMS

SQUARE HOLE

 

 

 

 

 

ENGINE PULLEY

RETAINER SPRING

 

FRONT LINK

ANTI-SWAY BAR

 

RETAINER SPRINGS

COLLAR

 

(BOTH SIDES)

 

 

HOUSING GUIDE

 

 

LARGE RETAINER

02695

 

SPRING

CLUTCH SPRING

DEFLECTOR SHIELD

 

 

BRACKET

 

 

FIG. 13

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Always Wear EYE Protection During Operation HD13538II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport Reverse Operation System ROSTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Transaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

195383 specifications

The Weed Eater 195383 is a standout model in the world of outdoor gardening tools, designed to provide efficient and effective grass trimming and edging solutions. This versatile tool is particularly popular among homeowners and landscaping professionals alike, thanks to its blend of functionality, ease of use, and innovative features.

One of the defining characteristics of the Weed Eater 195383 is its lightweight design. Weighing in at just a few pounds, it allows for easy maneuverability, making it perfect for tackling those tricky spots around flower beds, trees, and fences. The tool's ergonomic handle significantly enhances comfort during extended use, reducing strain on the hands and arms while you work.

The Weed Eater 195383 sports a powerful electric motor, which delivers consistent performance without the hassle of mixing fuel or dealing with exhaust fumes. This eco-friendly feature appeals to environmentally conscious users, minimizing carbon footprint while ensuring a clean working environment. With its quiet operation, you can also operate it in residential areas without disturbing your neighbors.

This model is equipped with a patented automatic feed spool system that releases the cutting line as needed. This means you won’t need to stop and manually adjust the line, allowing for uninterrupted work. The dual-line cutting system enhances trimming efficiency, cutting a broader swath of grass with each pass, which saves time and effort.

In terms of technology, the Weed Eater 195383 features a robust cutting head that can handle various types of grass and vegetation. It offers adjustable cutting lengths, letting users customize their trimming height based on specific yard needs. The head is designed for easy replacement of the cutting line, a process that even novice users can perform without hassle.

Ultimately, the Weed Eater 195383 combines user-friendly features with powerful performance, making it an essential tool for maintaining a neat and tidy yard. Whether you’re a casual gardener or a dedicated landscaper, this model is engineered to meet your trimming needs efficiently, transforming your outdoor space into a well-manicured oasis. With its reliability and thoughtful design, the Weed Eater 195383 is poised to become your go-to garden companion.
Top Page Image Contents