Weed Eater 165412, HD12538G manual Mowing Tips, To Start Engine See Fig

Page 13

OPERATION

TO START ENGINE (See Fig. 6)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

Sit on seat in operating position, depress clutchlbrake pedal and set parking brake.

*Place gear shift lever in neutral (N) position.

Move attachment clutch to "DISENGAGED"position.

*Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

Insert key into ignition and turn key clockwise to "START" position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throt- tle control back to the choke position and retry.

WARM WEATHER STARTING (50" F and above)

When engine starts, move the throttle control to the fast position.

*The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50"F and below)

When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period f r ~ mseveral seconds to several minutes, depending on the temperature.

The attachments can also be used during the engine warm- up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See 'TOADJUST CARBURETOR" in the Service and Adjustments section of this manual.

MOWING TIPS

*Tire chains cannot be used when the mower housing is attached to tractor.

*Mower should be properly leveled for best mowing perfor- mance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.

Use the runner on the right hand side of mower as a guide. The blade cuts approximately an inch outside the runner (See Fig. 7).

*The left hand side of mower should be used for trimming.

8Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clip- pings and more uniform cutting.

*When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, dri- veways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 8).

If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clippings.

Make first cut relatively high; the second to the desired

height.,

0Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

*Always operate engine at full throttle when mowing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

When operating attachments, select a ground speed that will suit the terrain and give best performance of the attach- ment being used.

FIG. 8

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Ownersmanual General Operation IV. ServiceSlope Operation III. ChildrenCustomer RESPONSIBILlflES Table of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Unpack CartonConnect Battery See Figs WOW to SET UP Your TractorInstall Seat See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemIng Know Your Tractor OperationHOW to USE Your Tractor To Transport Before Starting the EngineADD Gasoline To Operate on HillsTo Start Engine See Fig Mowing TipsCustomer Responsibil Lubricktion ChartNance Schedule Before Each USEBrake Operation TractorTires Blade CareBArrERY Customer ResponsibilitiesBelts Transaxle CoolingCustomer Responsib Clean AIR Screen See FigAIR Filter See Fig Engine Cooling Fins See FigMuffler CleaningSpark Plugs IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTO- Level Mower Housing Service and AdjustmentsBelt Removal To Replace Mower Blade Drive Belt See FigFront Wheel TOE-INICAMBER To Adjust Sfeeringwheel AlignmentTo Remove Wheel for Repairs See Fig T0,START Engine with a Weak BAlTERY See Fig To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysSee Fig To Adjust Throttle Control CableEngine StorageCorrection Troubleshoot NG PointsProblem Troubleshooting PointsService Notes Tractor - Model Number HD12538G SchematicElectrical Tractor - Model Number HD125386Repair Parts Chassis and Enclosures KEY Part NO. NO. Description Tracwor - Model Number HDl2538GDrive TRACTOR- Model Number HD125386KEY Part Tragtor - MOD- Nlimber HB12538G Steering AssemblyTractor - Model Number HD125386 Tractor - Model Number HD12538C Seat AssemblyWheels & Tires DecalsKEY Part Description Engine Tractor - Model Nlimber HD125386Manufacturer LlFT Part Description LiftMower 128772 Peerless Transaxle Model Number REF Part NO. no Description Model Number HD12538GREF Part Description NO. no Service Notes CE Notes CE Notes Suggested Guide for Sighting Slopes for Safe Operation

165412, HD12538G specifications

The Weed Eater HD12538G,165412 is a powerful and efficient string trimmer designed to tackle even the most challenging yard maintenance tasks. Built with homeowners and landscaping professionals in mind, this tool combines robust performance with user-friendly features, making it a popular choice among gardening enthusiasts.

One of the standout features of the HD12538G is its potent 25cc 2-cycle engine. This engine is designed to provide ample power and torque, allowing users to trim grass, weeds, and overgrown vegetation with ease. Its lightweight construction enhances maneuverability, reducing fatigue during extended use and enabling users to navigate tight spaces or uneven terrain effortlessly.

Equipped with a flexible and durable dual-line head, the Weed Eater HD12538G efficiently delivers precise cutting action. The auto-feed spool technology automatically feeds the cutting line as needed, eliminating the hassle of manual adjustments and enabling users to maintain focus on their trimming tasks. The trimmer is also compatible with various line sizes, providing versatility to suit different cutting conditions.

In terms of design, the HD12538G features an ergonomic handle and a convenient shoulder strap, offering optimal comfort during operation. The adjustable handle allows for customizable height settings, catering to users of different statures and ensuring comfortable control whether trimming hedges or edging around sidewalks. This thoughtful design reduces strain on the arms and back, making yard work a less daunting task.

Another significant advantage of the Weed Eater HD12538G is its ease of use and straightforward assembly. Users can quickly set up the trimmer and be ready to go in no time, making it an ideal choice for those new to yard maintenance or those who are looking for a reliable tool without a steep learning curve.

In terms of technological advancements, the trimmer boasts a low-emission engine that adheres to environmental regulations. It enables users to maintain their gardens while minimizing their carbon footprint. This makes it not only a practical choice but also a responsible one for eco-conscious consumers.

Overall, the Weed Eater HD12538G,165412 stands out in the market for its powerful performance, ease of use, comfort features, and environmentally friendly design. Whether you're maintaining a small backyard or managing larger landscaping projects, this trimmer combines functionality with user-oriented design, setting a high standard for modern gardening tools.
Top Page Image Contents