Weed Eater HD12538G, 165412 manual Service and Adjustments, TO- Level Mower Housing

Page 20

SERVICE AND ADJUSTMENTS

TO- - LEVEL MOWER HOUSING

-

Adjust the mower while tractor is parked on level ground

or driveway. Make sure tires are properly inflated (See "'PRODUCTSPECIFICATIONS" on page 3 of this manu-

al). If tires are over or underinflated, YOU will not proper- ly adjust your mower.

SIDE-TO-SIDEADJUSTMENT (See Figs. 17 and 18) Raise mower to its highest position.

At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance "A" on both sides of mower should be the same or within 114" of each other.

*If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjust- ment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 118".

Recheck measurements after adjusting.

OF MOWER TO

FRONT-TO-BACKADJUSTMENT,(See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT 1s NEc-

ESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing

should be adjusted so that the front is approximately 118" to 112" lower than the rear when the mower is in its high-

est position.

Check adjustment on right side of tractor. Measure dis- tance "D" directly in front and behind the mandrel at bot- tom edge of mower housing as shown.

Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-318".

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower loosen nut "Enon both front links an equal number of turns.

*When distance "D" is 118" to 112" lower at front than rear, tighten nuts "F"against trunnion on both front links.

*To raise front of mower, loosen nut "F" from trunnion on both front links. Tighten nut "Enon both front links an equal number of turns.

When distance "D" is 118" to 112" lower at front than rear, tighten nut "F" against trunnion on both front links.

Recheck side-to-sideadjustment.

I

-.a a -

SUSPENSION

FIG. 18

FIG. 19

I

FRONTLINKS

TRUNNION

I

FIG. 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Ownersmanual IV. Service General OperationSlope Operation III. ChildrenCustomer RESPONSIBILlflES Table of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonInstall Seat See Fig WOW to SET UP Your TractorConnect Battery See Figs Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemIng Operation Know Your TractorHOW to USE Your Tractor Before Starting the Engine To TransportADD Gasoline To Operate on HillsMowing Tips To Start Engine See FigLubricktion Chart Customer ResponsibilNance Schedule Before Each USETractor Brake OperationTires Blade CareCustomer Responsibilities BArrERYBelts Transaxle CoolingClean AIR Screen See Fig Customer ResponsibAIR Filter See Fig Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Remove Mower See FigService and Adjustments TO- Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Remove Wheel for Repairs See Fig To Adjust Sfeeringwheel AlignmentFront Wheel TOE-INICAMBER To Remove Hood and Grill Assembly See Fig T0,START Engine with a Weak BAlTERY See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See FigStorage EngineTroubleshoot NG Points CorrectionTroubleshooting Points ProblemService Notes Schematic Tractor - Model Number HD12538GTractor - Model Number HD125386 ElectricalRepair Parts Chassis and Enclosures Tracwor - Model Number HDl2538G KEY Part NO. NO. DescriptionTRACTOR- Model Number HD125386 DriveKEY Part Steering Assembly Tragtor - MOD- Nlimber HB12538GTractor - Model Number HD125386 Seat Assembly Tractor - Model Number HD12538CKEY Part Description DecalsWheels & Tires Tractor - Model Nlimber HD125386 EngineManufacturer LlFT Lift Part DescriptionMower 128772 Peerless Transaxle Model Number REF Part Description NO. no Model Number HD12538GREF Part NO. no Description Service Notes CE Notes CE Notes Suggested Guide for Sighting Slopes for Safe Operation

165412, HD12538G specifications

The Weed Eater HD12538G,165412 is a powerful and efficient string trimmer designed to tackle even the most challenging yard maintenance tasks. Built with homeowners and landscaping professionals in mind, this tool combines robust performance with user-friendly features, making it a popular choice among gardening enthusiasts.

One of the standout features of the HD12538G is its potent 25cc 2-cycle engine. This engine is designed to provide ample power and torque, allowing users to trim grass, weeds, and overgrown vegetation with ease. Its lightweight construction enhances maneuverability, reducing fatigue during extended use and enabling users to navigate tight spaces or uneven terrain effortlessly.

Equipped with a flexible and durable dual-line head, the Weed Eater HD12538G efficiently delivers precise cutting action. The auto-feed spool technology automatically feeds the cutting line as needed, eliminating the hassle of manual adjustments and enabling users to maintain focus on their trimming tasks. The trimmer is also compatible with various line sizes, providing versatility to suit different cutting conditions.

In terms of design, the HD12538G features an ergonomic handle and a convenient shoulder strap, offering optimal comfort during operation. The adjustable handle allows for customizable height settings, catering to users of different statures and ensuring comfortable control whether trimming hedges or edging around sidewalks. This thoughtful design reduces strain on the arms and back, making yard work a less daunting task.

Another significant advantage of the Weed Eater HD12538G is its ease of use and straightforward assembly. Users can quickly set up the trimmer and be ready to go in no time, making it an ideal choice for those new to yard maintenance or those who are looking for a reliable tool without a steep learning curve.

In terms of technological advancements, the trimmer boasts a low-emission engine that adheres to environmental regulations. It enables users to maintain their gardens while minimizing their carbon footprint. This makes it not only a practical choice but also a responsible one for eco-conscious consumers.

Overall, the Weed Eater HD12538G,165412 stands out in the market for its powerful performance, ease of use, comfort features, and environmentally friendly design. Whether you're maintaining a small backyard or managing larger landscaping projects, this trimmer combines functionality with user-oriented design, setting a high standard for modern gardening tools.
Top Page Image Contents