Weed Eater 183670 manual Mowing Tips, To Start Engine See Fig

Page 13

OPERATION

TO START ENGINE (See Fig. 5)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place gear shift lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the tempera- ture.

•The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

MOWING TIPS

•Tire chains cannot be used when the mower housing is attached to tractor.

•Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trimming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 7 ).

FIG. 7

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mowing to assure better mowing performance and proper dis- charge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting perfor- mance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model NO. WE12538L IV. Service Safety RulesGeneral Operation II. Slope OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Unassembled PartsTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsService Dates Lubrication ChartCustomer Responsibilities General RecommendationsBrake Operation TractorTires Operator Presence SystemEngine BatteryBelts Transaxle CoolingTo Service PRE-CLEANER Clean AIR ScreenTo Service Cartridge Engine Cooling Fins See FigMuffler CleaningSpark Plugs IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel Alignment To Adjust Brake See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Replace Headlight Bulb To Adjust CarburetorInterlocks and Relays To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number WE12538L, Product no 56 SchematicElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 140044X428 Optional Equipment 170551 Control Th/ch Flag Seat Wheels & Tires DecalsLSB42 LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

183670 specifications

The Weed Eater 183670 is a remarkable string trimmer designed for homeowners who seek efficiency and ease in lawn care. This versatile tool is particularly well-suited for trimming overgrown grass and weeds, allowing users to achieve a well-manicured garden with minimal effort.

One of the main features of the Weed Eater 183670 is its lightweight design, which enhances user maneuverability and reduces fatigue during extended periods of use. Weighing in at just under ten pounds, this trimmer is easy to carry and handle, making it an ideal choice for individuals looking to tackle their yard work without strain.

Powering this string trimmer is a potent 25cc 2-cycle engine. This powerful engine is designed to provide ample cutting power while ensuring efficient fuel consumption. The engine's performance is complemented by a heavy-duty flexible shaft that offers both durability and flexibility, allowing users to navigate around obstacles and reach tight spots with ease.

Another defining characteristic of the Weed Eater 183670 is its easy-to-use bump feed line system. This innovative design allows users to effortlessly extend the trimmer line with a simple tap on the ground, ensuring continuous cutting with minimal interruptions. The trimmer is also compatible with a range of replacement strings, allowing for customization based on specific trimming needs.

The Weed Eater 183670 is equipped with a 16-inch cutting width, providing ample coverage to make quick work of overgrown patches. Additionally, the trimmer head can tilt, giving users the ability to easily maneuver and trim in various positions, including under bushes and along edges. This feature enhances precision and ensures a clean, professional-looking cut.

Moreover, its ergonomic handle has been designed for comfort, featuring a soft-touch grip that reduces vibrations and improves control. The adjustable handle height accommodates users of different heights, making it a user-friendly option for a wide range of homeowners.

With a combination of power, user-friendly features, and innovative technology, the Weed Eater 183670 stands out as a practical choice for residential lawn maintenance. Whether you need to handle tough weeds or maintain your lawn's edges, this trimmer is designed to deliver dependable performance while ensuring an enjoyable mowing experience.
Top Page Image Contents