Weed Eater 183670 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse, Engine

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 26)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 26

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 27)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

 

GOVERNOR

GOVERNOR

 

CONTROL

 

CONTROL LEVER

 

PLATE

 

 

HOLES “A”

CLAMP

THROTTLE

 

SCREW

CABLE

 

 

FIG. 27

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. WE12538L II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsGeneral Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenTo Service PRE-CLEANER To Service CartridgeIN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Brake See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Remove CABLES, Reverse Order To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE12538L, Product no 56 SchematicElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 140044X428 Optional Equipment 170551 Control Th/ch Flag Seat LBD48 DecalsWheels & Tires LSB42Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

183670 specifications

The Weed Eater 183670 is a remarkable string trimmer designed for homeowners who seek efficiency and ease in lawn care. This versatile tool is particularly well-suited for trimming overgrown grass and weeds, allowing users to achieve a well-manicured garden with minimal effort.

One of the main features of the Weed Eater 183670 is its lightweight design, which enhances user maneuverability and reduces fatigue during extended periods of use. Weighing in at just under ten pounds, this trimmer is easy to carry and handle, making it an ideal choice for individuals looking to tackle their yard work without strain.

Powering this string trimmer is a potent 25cc 2-cycle engine. This powerful engine is designed to provide ample cutting power while ensuring efficient fuel consumption. The engine's performance is complemented by a heavy-duty flexible shaft that offers both durability and flexibility, allowing users to navigate around obstacles and reach tight spots with ease.

Another defining characteristic of the Weed Eater 183670 is its easy-to-use bump feed line system. This innovative design allows users to effortlessly extend the trimmer line with a simple tap on the ground, ensuring continuous cutting with minimal interruptions. The trimmer is also compatible with a range of replacement strings, allowing for customization based on specific trimming needs.

The Weed Eater 183670 is equipped with a 16-inch cutting width, providing ample coverage to make quick work of overgrown patches. Additionally, the trimmer head can tilt, giving users the ability to easily maneuver and trim in various positions, including under bushes and along edges. This feature enhances precision and ensures a clean, professional-looking cut.

Moreover, its ergonomic handle has been designed for comfort, featuring a soft-touch grip that reduces vibrations and improves control. The adjustable handle height accommodates users of different heights, making it a user-friendly option for a wide range of homeowners.

With a combination of power, user-friendly features, and innovative technology, the Weed Eater 183670 stands out as a practical choice for residential lawn maintenance. Whether you need to handle tough weeds or maintain your lawn's edges, this trimmer is designed to deliver dependable performance while ensuring an enjoyable mowing experience.
Top Page Image Contents