Weed Eater 183670 manual Off

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves

 

 

 

corrected, contact an authorized service center/

seat with attachment

 

 

 

department.

clutch engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Engine “backfires”

1.

Engine throttle control not set at “SLOW”

1.

Move throttle control to “SLOW” position and allow

when turning engine

 

position for 30 seconds before stopping engine.

 

to idle for 30 seconds before stopping engine.

“OFF”

 

 

 

 

 

 

 

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Model NO. WE12538L General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigCustomer Responsibilities Lubrication ChartService Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingTo Service Cartridge Clean AIR ScreenTo Service PRE-CLEANER Engine Cooling Fins See FigSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove CABLES, Reverse OrderInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE12538L, Product no 56Electrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 140044X428 Optional Equipment 170551 Control Th/ch Flag Seat LSB42 DecalsWheels & Tires LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

183670 specifications

The Weed Eater 183670 is a remarkable string trimmer designed for homeowners who seek efficiency and ease in lawn care. This versatile tool is particularly well-suited for trimming overgrown grass and weeds, allowing users to achieve a well-manicured garden with minimal effort.

One of the main features of the Weed Eater 183670 is its lightweight design, which enhances user maneuverability and reduces fatigue during extended periods of use. Weighing in at just under ten pounds, this trimmer is easy to carry and handle, making it an ideal choice for individuals looking to tackle their yard work without strain.

Powering this string trimmer is a potent 25cc 2-cycle engine. This powerful engine is designed to provide ample cutting power while ensuring efficient fuel consumption. The engine's performance is complemented by a heavy-duty flexible shaft that offers both durability and flexibility, allowing users to navigate around obstacles and reach tight spots with ease.

Another defining characteristic of the Weed Eater 183670 is its easy-to-use bump feed line system. This innovative design allows users to effortlessly extend the trimmer line with a simple tap on the ground, ensuring continuous cutting with minimal interruptions. The trimmer is also compatible with a range of replacement strings, allowing for customization based on specific trimming needs.

The Weed Eater 183670 is equipped with a 16-inch cutting width, providing ample coverage to make quick work of overgrown patches. Additionally, the trimmer head can tilt, giving users the ability to easily maneuver and trim in various positions, including under bushes and along edges. This feature enhances precision and ensures a clean, professional-looking cut.

Moreover, its ergonomic handle has been designed for comfort, featuring a soft-touch grip that reduces vibrations and improves control. The adjustable handle height accommodates users of different heights, making it a user-friendly option for a wide range of homeowners.

With a combination of power, user-friendly features, and innovative technology, the Weed Eater 183670 stands out as a practical choice for residential lawn maintenance. Whether you need to handle tough weeds or maintain your lawn's edges, this trimmer is designed to deliver dependable performance while ensuring an enjoyable mowing experience.
Top Page Image Contents