Weed Eater 183670 To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 15 and 16)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM EDGE

OF MOWER TO

OF MOWER TO

GROUND

GROUND

 

A

A

 

GROUND

 

LINE

FIG. 15

SUSPENSION

ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 16

FRONT-TO-BACK ADJUSTMENT (See Figs. 17 and 18)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”“D”

FIG. 17

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “E”

NUT “F”

FRONT

LINKSTRUNNION

FIG. 18

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 19)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Disconnect R.H. suspension arm from rear deck bracket by removing retainer spring.

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work new belt around both mandrel pulleys and idler pulleys.

•Install new belt into engine pulley grove.

•Reconnect R.H. suspension arm and secure with re- tainer spring.

•Make sure belt is in all pulley grooves and inside all belt

20 guides.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. WE12538L Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering WheelAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigLubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig To Adjust Steering Wheel AlignmentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE12538L, Product no 56Electrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 140044X428 Optional Equipment 170551 Control Th/ch Flag Seat Decals Wheels & TiresLSB42 LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

183670 specifications

The Weed Eater 183670 is a remarkable string trimmer designed for homeowners who seek efficiency and ease in lawn care. This versatile tool is particularly well-suited for trimming overgrown grass and weeds, allowing users to achieve a well-manicured garden with minimal effort.

One of the main features of the Weed Eater 183670 is its lightweight design, which enhances user maneuverability and reduces fatigue during extended periods of use. Weighing in at just under ten pounds, this trimmer is easy to carry and handle, making it an ideal choice for individuals looking to tackle their yard work without strain.

Powering this string trimmer is a potent 25cc 2-cycle engine. This powerful engine is designed to provide ample cutting power while ensuring efficient fuel consumption. The engine's performance is complemented by a heavy-duty flexible shaft that offers both durability and flexibility, allowing users to navigate around obstacles and reach tight spots with ease.

Another defining characteristic of the Weed Eater 183670 is its easy-to-use bump feed line system. This innovative design allows users to effortlessly extend the trimmer line with a simple tap on the ground, ensuring continuous cutting with minimal interruptions. The trimmer is also compatible with a range of replacement strings, allowing for customization based on specific trimming needs.

The Weed Eater 183670 is equipped with a 16-inch cutting width, providing ample coverage to make quick work of overgrown patches. Additionally, the trimmer head can tilt, giving users the ability to easily maneuver and trim in various positions, including under bushes and along edges. This feature enhances precision and ensures a clean, professional-looking cut.

Moreover, its ergonomic handle has been designed for comfort, featuring a soft-touch grip that reduces vibrations and improves control. The adjustable handle height accommodates users of different heights, making it a user-friendly option for a wide range of homeowners.

With a combination of power, user-friendly features, and innovative technology, the Weed Eater 183670 stands out as a practical choice for residential lawn maintenance. Whether you need to handle tough weeds or maintain your lawn's edges, this trimmer is designed to deliver dependable performance while ensuring an enjoyable mowing experience.
Top Page Image Contents