Weed Eater 96048000100, 435057 manual Mowing Tips, To Start Engine See Fig

Page 13

OPERATION

TO START ENGINE (See Fig. 4)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place gear shift lever in neutral position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F/10° C and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F/10° C and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

•The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32° F/0°C) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjust- ments section of this manual.

MOWING TIPS

•Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 12).

Fig. 12

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 960480001 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Steering Wheel Unassembled PartsTools Required for Assembly AssemblyToremovetractorfromcarton Before Removing Tractor from SkidCheck Brake System Install Seat See FigOperation Know Your Tractor Attachment Clutch Switch Disengaged Engaged HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigUsing the Reverse Operation System To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig Reverse Operation System ROS See FigBefore Starting the Engine To Start Engine See Fig Mowing TipsMaintenance MaintenanceGeneral Recommendations ScheduleBlade Care TractorBlade Removal See Fig Brake OperationTransaxle Maintenance BatteryEngine BeltsClean AIR Screen CleaningAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Raise attachment lift lever to highest position To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel Alignment Transaxle Gear Shift Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig To Remove Wheel See FigTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Interlocks and RelaysOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsExcessive Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimited Warranty
Related manuals
Manual 20 pages 55.1 Kb

960480001, 96048000100, 435057 specifications

The Weed Eater 960480001, 96048000100, and 435057 are popular models designed for efficient lawn maintenance and landscaping. Renowned for their performance and reliability, these weed eaters are essential tools for both professional landscaping services and homeowners who desire a pristine yard.

One prominent feature of the Weed Eater line is its lightweight design, making it easy to maneuver around garden beds, trees, and other obstacles. Weighing significantly less than many competitive options, these models reduce fatigue during extended use, allowing users to tackle large areas without discomfort.

The 960480001 and 96048000100 models come equipped with powerful 27cc or higher engines, delivering ample power for tackling thick grass and weeds. Their advanced gas-powered engines ensure longer run times, allowing users to complete their tasks without frequent refueling. The 435057 model, on the other hand, features a reliable electric motor, appealing to those who prefer a quieter and more environmentally friendly option.

All models incorporate a patented Easy Start technology, which minimizes the effort required to start the engine. This feature is particularly beneficial to novice users, as it simplifies the operation of the weed eater. Additionally, the automatic line feed system ensures a steady supply of trimming line, reducing interruptions during operation and allowing users to work continuously on their landscaping tasks.

The ergonomic design of the Weed Eater includes adjustable handles, providing comfort and control during use. The cushioned grips absorb vibrations, enhancing user comfort and reducing strain on the hands and arms. Moreover, the flex shaft technology found in these models improves durability while allowing flexibility in difficult-to-reach areas.

Safety features, such as protective shields and easy-access controls, further enhance the usability of these weed eaters. The robust construction ensures longevity, even under challenging conditions, making them a reliable choice for regular use.

In summary, the Weed Eater 960480001, 96048000100, and 435057 models stand out for their lightweight design, powerful engines, easy-start technology, and user-friendly features. Whether you’re a homeowner or a professional landscaper, these weed eaters are designed to meet your lawn care needs efficiently and effectively.
Top Page Image Contents