Weed Eater 435057, 96048000100 manual To Level Mower, Visual SIDE-TO-SIDE Adjustment See Fig

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 26)

•With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

•With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower LH side of mower, or, to the right to raise LH side of mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

02948

 

Fig. 26

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 27)

•With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blade is sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to its highest position.

•At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

Fig. 27

•If adjustment is necessary, see step in Visual Adjust- ment instructions above.

•Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 28 & 29) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 3/8" lower than the rear tip when the mower is in its highest position.

CAUTION: Blade is sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to highest position.

•Position blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

BB

Fig. 28

•If front tip of blade is not 1/8" to 3/8" lower than the rear tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (ltighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

B

A

TIGHTEN ADJUST

LOOSEN

ADJUST NUT

NUT B TO RAISE

B TO LOWER

MOWER

 

02950

MOWER

 

LOOSEN JAM NUT A FIRST

 

Fig. 29

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 3/8" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 960480001 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering WheelAssembly Tools Required for AssemblyToremovetractorfromcarton Before Removing Tractor from SkidInstall Seat See Fig Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Attachment Clutch Switch Disengaged EngagedTo SET Parking Brake See Fig Stopping See FigTo Adjust Mower Cutting Height See Fig Using the Reverse Operation SystemTo Move Forward and Backward See Fig Reverse Operation System ROS See FigBefore Starting the Engine Mowing Tips To Start Engine See FigMaintenance MaintenanceGeneral Recommendations ScheduleTractor Blade CareBlade Removal See Fig Brake OperationBattery Transaxle MaintenanceEngine BeltsCleaning Clean AIR ScreenAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig To Remove Wheel See FigTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty
Related manuals
Manual 20 pages 55.1 Kb

960480001, 96048000100, 435057 specifications

The Weed Eater 960480001, 96048000100, and 435057 are popular models designed for efficient lawn maintenance and landscaping. Renowned for their performance and reliability, these weed eaters are essential tools for both professional landscaping services and homeowners who desire a pristine yard.

One prominent feature of the Weed Eater line is its lightweight design, making it easy to maneuver around garden beds, trees, and other obstacles. Weighing significantly less than many competitive options, these models reduce fatigue during extended use, allowing users to tackle large areas without discomfort.

The 960480001 and 96048000100 models come equipped with powerful 27cc or higher engines, delivering ample power for tackling thick grass and weeds. Their advanced gas-powered engines ensure longer run times, allowing users to complete their tasks without frequent refueling. The 435057 model, on the other hand, features a reliable electric motor, appealing to those who prefer a quieter and more environmentally friendly option.

All models incorporate a patented Easy Start technology, which minimizes the effort required to start the engine. This feature is particularly beneficial to novice users, as it simplifies the operation of the weed eater. Additionally, the automatic line feed system ensures a steady supply of trimming line, reducing interruptions during operation and allowing users to work continuously on their landscaping tasks.

The ergonomic design of the Weed Eater includes adjustable handles, providing comfort and control during use. The cushioned grips absorb vibrations, enhancing user comfort and reducing strain on the hands and arms. Moreover, the flex shaft technology found in these models improves durability while allowing flexibility in difficult-to-reach areas.

Safety features, such as protective shields and easy-access controls, further enhance the usability of these weed eaters. The robust construction ensures longevity, even under challenging conditions, making them a reliable choice for regular use.

In summary, the Weed Eater 960480001, 96048000100, and 435057 models stand out for their lightweight design, powerful engines, easy-start technology, and user-friendly features. Whether you’re a homeowner or a professional landscaper, these weed eaters are designed to meet your lawn care needs efficiently and effectively.
Top Page Image Contents