Weed Eater 96048000100, 435057 manual Engine, Battery, Belts, Transaxle Maintenance, Lubrication

Page 16

MAINTENANCE

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

NOTE:Theoriginalequipmentbatteryonyourtractorismain- tenance free. Do not attempt to open or remove caps or cov- ers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

Raise seat.

Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

Rinse the battery with plain water and dry.

Clean terminals and battery cable ends with wire brush until bright.

Coat terminals with grease or petroleum jelly.

Reinstall battery (See “REPLACING BATTERY" in the SERVICEANDADJUSTMENTSsectionofthismanual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE MAINTENANCE

Keep transaxle free from build-up of dirt and chaff which can restrict cooling.

Do not attempt to clean transaxle while engine is running or while the transaxle is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transaxle.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

SAE 30

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

-20

0

 

 

30 32 40

 

60

80

100

C

-30

-20

-10

0

10

20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

Fig. 15

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, they will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the tractor is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Fig. 16)

Determine temperature range expected before oil change. All oil must meet API service classification C.

Be sure tractor is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

CAUTION: If engine has been operated for an extended period of time immedi- ately prior to draining oil, oil will be hot.

OIL DRAIN HOLE

OIL

DRAIN

PLUG

OIL DRAIN

EXTENSION

Fig. 16

Slide oil drain extension under oil drain hole (drain hole maybeflushwithorprotrudefromengineblocksidewall).

Make sure back face of oil drain extension is flush with engine side wall.

Make sure bottom lip of oil drain extension is lined up with bottom of oil drain hole.

Position a container to catch oil directly under front end of oil drain extension.

Slide a 1/2” (12 point) socket mounted on an extension onto oil drain plug.

Loosen plug while holding the oil drain extension firmly in place.

Drain oil into container.

After oil has drained completely, reinstall oil drain plug. (Do not tighten more than 13 Ft. Lbs.)

Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick. Tighten cap onto the tube securely when finished.

16

Image 16
Contents 960480001 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering WheelAssembly Tools Required for AssemblyToremovetractorfromcarton Before Removing Tractor from SkidInstall Seat See Fig Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Attachment Clutch Switch Disengaged EngagedTo SET Parking Brake See Fig Stopping See FigTo Adjust Mower Cutting Height See Fig Using the Reverse Operation SystemTo Move Forward and Backward See Fig Reverse Operation System ROS See FigBefore Starting the Engine Mowing Tips To Start Engine See FigMaintenance MaintenanceGeneral Recommendations ScheduleTractor Blade CareBlade Removal See Fig Brake OperationBattery Transaxle MaintenanceEngine BeltsCleaning Clean AIR ScreenAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig To Remove Wheel See FigTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty
Related manuals
Manual 20 pages 55.1 Kb

960480001, 96048000100, 435057 specifications

The Weed Eater 960480001, 96048000100, and 435057 are popular models designed for efficient lawn maintenance and landscaping. Renowned for their performance and reliability, these weed eaters are essential tools for both professional landscaping services and homeowners who desire a pristine yard.

One prominent feature of the Weed Eater line is its lightweight design, making it easy to maneuver around garden beds, trees, and other obstacles. Weighing significantly less than many competitive options, these models reduce fatigue during extended use, allowing users to tackle large areas without discomfort.

The 960480001 and 96048000100 models come equipped with powerful 27cc or higher engines, delivering ample power for tackling thick grass and weeds. Their advanced gas-powered engines ensure longer run times, allowing users to complete their tasks without frequent refueling. The 435057 model, on the other hand, features a reliable electric motor, appealing to those who prefer a quieter and more environmentally friendly option.

All models incorporate a patented Easy Start technology, which minimizes the effort required to start the engine. This feature is particularly beneficial to novice users, as it simplifies the operation of the weed eater. Additionally, the automatic line feed system ensures a steady supply of trimming line, reducing interruptions during operation and allowing users to work continuously on their landscaping tasks.

The ergonomic design of the Weed Eater includes adjustable handles, providing comfort and control during use. The cushioned grips absorb vibrations, enhancing user comfort and reducing strain on the hands and arms. Moreover, the flex shaft technology found in these models improves durability while allowing flexibility in difficult-to-reach areas.

Safety features, such as protective shields and easy-access controls, further enhance the usability of these weed eaters. The robust construction ensures longevity, even under challenging conditions, making them a reliable choice for regular use.

In summary, the Weed Eater 960480001, 96048000100, and 435057 models stand out for their lightweight design, powerful engines, easy-start technology, and user-friendly features. Whether you’re a homeowner or a professional landscaper, these weed eaters are designed to meet your lawn care needs efficiently and effectively.