Weed Eater 435057 manual Tools Required for Assembly, Toremovetractorfromcarton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

5/16" wrench

Utility knife

(2)

7/16" wrenches

Tire pressure gauge

(2) 1/2" wrenches

Pliers

(1)

9/16" wrench

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TOREMOVETRACTORFROMCARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

•Lift seat to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

•For battery and battery cable installation see "RE- PLACING BATTERY" in the "Service and Adjustments" section in this manual.

LABEL

Fig. 1

TO INSTALL STEERING WHEEL (See Fig. 2)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, lock washer, hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

BOLT

LOCK

WASHER

LARGE

FLAT WASHER

STEERING

WHEEL

STEERING

BOOT

ADAPTER

EXTENSION SHAFT

LOWER

STEERING

SHAFT

Fig. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 960480001 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering WheelToremovetractorfromcarton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigUsing the Reverse Operation System Reverse Operation System ROS See FigBefore Starting the Engine Mowing Tips To Start Engine See FigGeneral Recommendations MaintenanceMaintenance ScheduleBlade Removal See Fig TractorBlade Care Brake OperationEngine BatteryTransaxle Maintenance BeltsAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Remove Wheel See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty
Related manuals
Manual 20 pages 55.1 Kb

960480001, 96048000100, 435057 specifications

The Weed Eater 960480001, 96048000100, and 435057 are popular models designed for efficient lawn maintenance and landscaping. Renowned for their performance and reliability, these weed eaters are essential tools for both professional landscaping services and homeowners who desire a pristine yard.

One prominent feature of the Weed Eater line is its lightweight design, making it easy to maneuver around garden beds, trees, and other obstacles. Weighing significantly less than many competitive options, these models reduce fatigue during extended use, allowing users to tackle large areas without discomfort.

The 960480001 and 96048000100 models come equipped with powerful 27cc or higher engines, delivering ample power for tackling thick grass and weeds. Their advanced gas-powered engines ensure longer run times, allowing users to complete their tasks without frequent refueling. The 435057 model, on the other hand, features a reliable electric motor, appealing to those who prefer a quieter and more environmentally friendly option.

All models incorporate a patented Easy Start technology, which minimizes the effort required to start the engine. This feature is particularly beneficial to novice users, as it simplifies the operation of the weed eater. Additionally, the automatic line feed system ensures a steady supply of trimming line, reducing interruptions during operation and allowing users to work continuously on their landscaping tasks.

The ergonomic design of the Weed Eater includes adjustable handles, providing comfort and control during use. The cushioned grips absorb vibrations, enhancing user comfort and reducing strain on the hands and arms. Moreover, the flex shaft technology found in these models improves durability while allowing flexibility in difficult-to-reach areas.

Safety features, such as protective shields and easy-access controls, further enhance the usability of these weed eaters. The robust construction ensures longevity, even under challenging conditions, making them a reliable choice for regular use.

In summary, the Weed Eater 960480001, 96048000100, and 435057 models stand out for their lightweight design, powerful engines, easy-start technology, and user-friendly features. Whether you’re a homeowner or a professional landscaper, these weed eaters are designed to meet your lawn care needs efficiently and effectively.
Top Page Image Contents