McCulloch MC30 manual Install Seat, To Adjust Seat, Front and Back, Lumbar Support

Page 8

INSTALL SEAT

1.Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to riding mower. Remove the cardboard packing and discard.

2.Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

3.Push down on seat to engage pads in slots and pull seat towards rear of riding mower.

4.Raise seat and tighten bolt and large flat washer securely.

5.Remove tape and discard.

6.Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat.

Slot

Tape

Pad

Flat washer

Seat pan

Bolt

Tab

Adjustment

handle

TO ADJUST SEAT

FRONT AND BACK -

Sit in seat.

Lift up adjustment lever and slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

Release lever to lock seat in position.

Lumbar

 

Adjustment Knob

Adjustment Lever

LUMBAR SUPPORT -

Loosen lumbar adjustment knob.

Slide seat back up or down to most com- fortable position for lower back support.

Tighten lumbar adjustment knob.

NOTE: You may now roll your riding mower off the skid. Follow the appropriate instruction below to remove the riding mower from the skid.

WARNING: Before starting, read, un- derstand and follow all instructions in the Operation section of this manual. Be sure riding mower is in a well-ventilated area. Be sure the area in front of riding mower is clear of other people and objects.

TO ROLL RIDING MOWER OFF SKID (See Operation section for location and function of controls)

1.Raise deck lift lever to its highest position.

2.Release parking brake by depressing clutch/brake pedal.

3.Shift unit to neutral.

4.Roll riding mower forward off skid.

RIDING MOWER

STEERING

MODEL NUMBER MC30 (96022001300)

PRODUCT NUMBER 960 22 00-13

KEY

PART

 

NO.

NO.

DESCRIPTION

1

532 44 20-64

WHEEL TUBE

2

812 00 00-01

E-CLIP

3532 18 89-67 WASHER, HARDENED

4532 12 17-49 WASHER, 1/4 X 3/4

5

532 43 61-81 SPINDLE, RH

6532 12 49-31 WASHER, HARDENED THRUST

7532 12 49-37 BUSHING, STEERING COLUMN

9

819 13 14-14 WASHER

10532 42 80-57 WELDMENT, LWR STRG SHAFT

11532 43 61-83 LINK, STRNG LH

12532 43 61-84 LINK, STRNG RH

13874 78 05-24 BOLT, 5/16-18 X 1 1/2

14819 11 12-16 WASHER 11/32 X 3/4 X 16 GA

16

532 43 62-82

BUSHING SNAP

15

873 80 05-00

NUT, 5/16-18

17

532 43 61-78

SUPPORT, UPPER STEERING

19817 00 05-12 BOLT, 5/16-18 X 3/4

20532 42 80-45 CLIP, RETAINER SPRING

23 532 43 77-47 ADAPTER, STEERING WHEEL

26532 42 45-51 WHEEL, STEERING

27532 44 15-06 CAP, STEERING WHEEL

28532 19 98-49 CLIP, RETAINER SPRING

29

532 43 61-80 SPINDLE LH

30532 19 32-68 CAP, HUB, AXLE

31819 34 32-10 WASHER 1-1/16 X 2 X 10GA.

32817 58 05-20 SCREW HEXWSH THD 5/16-18 X 1-3/4

34532 43 61-82 SHAFT STEERING UPPER

35532 44 20-66 BOOT LOWER STEERING WHEEL

36532 19 60-75 SHAFT EXTENSION STEERING SPLINE

37874 78 05-80 BOLT FIN HEX 5/16-18 UNC X 5 GR5

38810 04 05-00 WASHER LOCK HVY HLCL SPR 5/16

39 819 11 38-12 WASHER

41532 43 65-90 FOAM SHAFT STEERING

42532 42 10-76 PIN, 5/64 X 3/4 COTTER

43873 54 05-00 CROWNLOCK NUT 5/16-24 UNF

44

532 42 80-44 BUSHING

NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm

8

37

Image 8
Contents MC30 06.28.11 TH/BDService Notes Table of ContentsWarranty General Operation Service Notes Safety RulesAlways wear eye protection when operat- ing machine IV. Service II. Slope OperationIII. Children Safe Handling of GasolineNever operate machine in a closed area General ServiceRiding Mower Product Specifications Product SpecificationsRead and observe the safety rules Unassembled PartsASSEMBLY/PRE-OPERATION Tools Required for AssemblyHOW to SET UP Your Riding Mower To Remove Riding Mower fromInstall Seat To Adjust SeatFront and Back Lumbar SupportTo Attach Front Bumper Check Tire PressureTo Attach Rear Bumper Check Deck LevelnessChecklist Operation 89 88 107 111Brake into brake position Ignition Switch Used for starting and stopping the engineKnow Your Riding Mower HOW to USE Your Riding Mower To SET Parking BrakeGround Drive StoppingTo Adjust Mower Cutting Height To USE Throttle ControlTo Move Forward and Backward To Operate MowerUsing the Reverse Operation System Reverse Operation System ROSTo Attach Deflector To Operate on HillsBefore Starting the Engine To Start EngineCheck Engine OIL Level ADD GasolineTroubleshooting Chart Mowing TipsBefore Each USE MaintenanceGeneral Recommendations Battery StorageEngine OtherBattery To Start Engine with a Weak BatteryReplacing Battery Transaxle CoolingCleaning Service and Adjustments To Level Mower HousingTo Install Mower To Remove Mower

MC30 specifications

The McCulloch MC30 is a versatile and powerful chainsaw designed to meet the needs of both professional users and DIY enthusiasts alike. Known for its lightweight design and easy maneuverability, the MC30 allows users to tackle a variety of cutting tasks with confidence and efficiency.

One of the standout features of the McCulloch MC30 is its robust 30cc engine, which offers an excellent balance of power and efficiency. This engine is engineered with advanced technology that enables it to deliver high performance while minimizing fuel consumption. Users will appreciate the quick start technology, which reduces the effort required to start the chainsaw, making it more accessible for those who may not have extensive experience with power tools.

The MC30 is equipped with a high-quality 12-inch bar and chain, allowing for smooth, precise cuts in a range of materials. This is particularly beneficial when trimming branches, cutting firewood, or performing other outdoor maintenance tasks. The low kickback chain enhances safety while still providing the cutting power needed for effective performance.

Ergonomics play a significant role in the design of the McCulloch MC30. The chainsaw features a comfortable handle and an adjustable pivoting chain oil pump, which allows users to set the oil flow rate according to their cutting demands. This not only improves the longevity of the bar and chain but also ensures a seamless cutting experience.

Another innovative characteristic of the MC30 is its anti-vibration technology, which reduces the vibration transmitted to the user's hands. This feature is particularly crucial during extended use, as it helps decrease fatigue and increases overall comfort. The chainsaw also includes a tool-less chain tensioning system, allowing for easy adjustments to the chain without the need for additional tools.

Safety is an essential consideration in the design of the McCulloch MC30, which includes a chain brake feature that provides added protection against accidental chain movement. This model also sports a protective bar sheath for safe storage when the tool is not in use.

In summary, the McCulloch MC30 is a powerful yet lightweight chainsaw that combines performance and comfort. With its advanced engine technology, ergonomic design, and essential safety features, it is an ideal choice for anyone looking to undertake a variety of cutting tasks around the home or on the job site. Whether you're an experienced user or a newcomer, the MC30 delivers reliability and efficiency in a compact package.