McCulloch Essential Service and Adjustments for Mowcart 66 Lawn Mower
Page 18

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while riding mower is parked on level ground or driveway. Make sure tires are properly inflated (See side of tire for proper PSI). If tires are over or under- inflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•Measure distance "A" from bottom edge of mower to ground level at front corners of mower.

•To raise the right side of the mower, tighten lift link adjust- ment nut.

•To lower the right side of the mower, loosen lift link ad- justment nut.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

• Recheck measurements after adjusting.

Bottom Edge of Mower to

Bottom Edge of Mower to

Ground

Ground

A

A

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of riding mower. Measure distance “F” directly in front and behind the mandrel at bottom edge of mower housing as shown.

Nut "G"

Nut "H"

Trunnion

TO REPLACE MOWER BLADE DRIVE BELT

MOWER DRIVE BELT REMOVAL

1.Park riding mower on a level surface.

2.Set parking brake.

3.Lower mower to its lowest position.

4.Remove mandrel cover from mower deck.

5.Remove rear engine plate from unit.

6.Remove rear belt keeper from unit.

7.Carefully roll belt over the top of the mower blade mandrel.

8.Remove belt from idler pulleys.

Mower Drive Belt

•To lower front of mower housing turn nuts “G” and “H” clockwise.

FF

Mandrel

Belt

Keeper

Idler Pulleys

•When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on front link.

•To raise front of mower housing turn nuts “G” and “H” counter clockwise.

•When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on front link.

NOTE: Each full turn of "G" will change "F" by approxi- mately about 3/8".

• Recheck side-to-side adjustment.

9.Check idler pulleys to see that they rotate freely.

10.Remove belt from rear drive pulley.

MOWER DRIVE BELT INSTALLATION

Install in reverse order following instructions in "MOWER DRIVE BELT REMOVAL" section.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Mowcart Safety Rules General OperationII. Slope Operation IV. Service Safe Handling of Gasoline General ServiceIII. Children Table of Contents Unassembled Parts HOW to SET UP Your Riding Mower AssemblyTools Required for Assembly To Remove Riding Mower from CartonCheck Deck Levelness Check BatteryCheck Tire Pressure Check for Proper Positon of Mower Drive BeltOperation Know Your Riding Mower ROSHOW to USE Your Riding Mower To Operate on Hills Using the Reverse Operation SystemReverse Operation System ROS To TransportMowing Tips ADD GasolineTo Start Engine Recoil Starting SystemMaintenance General RecommendationsBefore Each USE Riding Mower Belt BatteryTransaxle Cooling EngineCleaning Clean AIR ScreenClean AIR INTAKE/COOLING Areas AIR FilterService and Adjustments To Install MowerTo Remove Mower To Level Mower Housing To Replace Mower Blade Drive BeltTo Start Engine with a Weak Battery To Adjust BrakeTo Adjust Steering Wheel Alignment Replacing BatteryInterlocks and Relays To Replace FuseStorage MowerOther Troubleshooting Points Mower blade will 06.02.10 CL

MOWCART 66, 532 43 67-90, 96021000900 specifications

The McCulloch 96021000900,532 43 67-90, MOWCART 66 is a versatile and robust lawn care solution designed for homeowners and landscape professionals alike. This innovative product combines power, functionality, and user-friendly features, making it an essential addition to any garden maintenance toolkit.

One of the standout features of the MOWCART 66 is its powerful engine. It is equipped with a reliable and efficient motor that delivers exceptional cutting performance. This ensures that even the toughest grass and overgrown areas are tackled with ease, providing a clean, even cut every time. The engine's design also emphasizes fuel efficiency, allowing users to complete larger tasks without frequent refueling.

The MOWCART 66 boasts a wide cutting deck, enabling it to cover substantial ground in a single pass. The adjustable cutting height feature allows users to customize their lawn care experience according to their preferences or the specific needs of their lawn. Whether it’s a manicured lawn or a more rugged terrain, the MOWCART 66 offers the adaptability required to meet diverse conditions.

The design of the MOWCART 66 places significant emphasis on user comfort and convenience. Its ergonomic handle makes maneuvering the machine effortless, reducing strain on the user during extended use. Additionally, the lightweight construction ensures that the unit remains easy to handle, even in tight spaces.

Another notable aspect of the McCulloch MOWCART 66 is its cutting technologies. The product incorporates advanced blade designs that enhance cutting efficiency and reduce the risk of clogging. This technology ensures that the clippings are finely chopped, allowing for better mulch distribution, which enriches the soil and promotes healthy grass growth.

Safety is paramount in the design of the MOWCART 66. It is equipped with various safety features to protect the user while in operation. These include a blade brake that stops the blades immediately when the user releases the handle, minimizing potential accidents.

In summary, the McCulloch 96021000900,532 43 67-90, MOWCART 66 represents a blend of power, adaptability, and ease of use. Its high-performance engine, wide cutting deck, and user-centric design make it a valuable tool for anyone looking to maintain a pristine outdoor space. Whether you're a seasoned landscaper or simply looking to keep your yard in top shape, the MOWCART 66 is engineered to meet your lawn care needs efficiently and effectively.
Top Page Image Contents