McCulloch 96041011600 manual Check Tire Pressure, Check Deck Levelness, Check Brake System

Page 8

ASSEMBLY

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

•Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is operating properly. See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.

✓CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PER- FORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

✓All assembly instructions have been completed.

✓No remaining loose parts in carton.

✓Battery is properly prepared and charged.

✓Seat is adjusted comfortably and tightened securely.

✓All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

✓Be sure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

✓Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

✓Check wiring. See that all connections are still secure and wires are properly clamped.

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

✓Engine oil is at proper level.

✓Fuel tank is filled with fresh, clean, regular unleaded gasoline.

✓Become familiar with all controls, their location and function. Operate them before you start the engine.

✓Be sure brake system is in safe operating condition.

✓Be sure Operator Presence System and Reverse Op- eration System (ROS) are working properly (See the Operation and Maintenance sections in this manual).

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents M13538 Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyToremovetractorfromcarton Before Removing Tractor from SkidInstall Seat See Fig Check Battery See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Attachment Clutch Lever Used to engageHOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Move Forward and Backward See FigTo Operate Mower To Stop Mower BladesBefore Starting the Engine Mowing Tips To Start Engine See FigMaintenance Lubrication ChartBlade Removal See Fig BatteryTractor Engine Cleaning IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs Install belt on engine pulley M Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation
Top Page Image Contents