McCulloch 96041011501 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 18

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

Depress clutch/brake pedal fully and set parking brake.

Place gearshift lever in neutral position.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key to “STOP” and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 19)

Place attachment clutch in “DISENGAGED” position.

Lower attachment lift lever to its lowest position.

Roll belt off engine pulley (M) and belt keepers (G).

Remove cable (P) by depressing tab (L).

Remove clutch cable spring (Q) from idler arm (R).

Disconnect front link (E) from mower - remove retainer spring and washer.

Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

CAUTION: AFTER REAR LIFT LINKS

ARE DISCONNECTED, THE ATTACH-

MENT LIFT LEVER WILL BE SPRING

LOADED. HAVE A TIGHT GRIP ON LIFT

LEVER WHEN CHANGING POSITION

OF THE LEVER.

Slide mower out from under right side of tractor.

B

A

R

C

D

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LINKS

(C)FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

TO INSTALL MOWER (See Fig. 19-24)

Be sure tractor is on level surface and engage parking brake.

Lower attachment lift lever to it's lowest position.

CAUTION: LIFT LEVER IS SPRING

LOADED. HAVE A TIGHT GRIP ON

LIFT LEVER, LOWER IT SLOWLY AND

ENGAGE IN LOWEST POSITION.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

Slide mower under tractor until it is centered under tractor.

MF

G

E

G

A

PL Q CD FIG. 19

18

Image 18
Contents M11577 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering WheelToremovetractorfromcarton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Operate Mower To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To Stop Mower BladesBefore Starting the Engine Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigBelts Transaxle MaintenanceEngine LubricationAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX10.29.09 BM

532 42 27-27 Rev. 2, 96041011501 specifications

The McCulloch 96041011501,532 42 27-27 Rev. 2 is a standout model within the McCulloch line of outdoor power equipment, known for its robust design and high-performance features. As a chain saw primarily aimed at professionals and dedicated homeowners, this model delivers an exceptional balance of power, precision, and user convenience.

One of the key features of the McCulloch 96041011501 is its powerful engine, which boasts a striking performance capability. With a robust engine displacement, this chainsaw is equipped to handle a variety of cutting tasks, from felling large trees to trimming branches with ease. The engine's design emphasizes fuel efficiency, helping users maximize their productivity while minimizing fuel consumption.

The 42 cm (16.5 inches) guide bar provides a perfect balance between maneuverability and cutting capacity. It allows for precise cuts in tight spaces while maintaining efficiency during larger cuts. The chain used in this model has been engineered for rapid cutting, ensuring that users can tackle tough jobs without excessive effort. Additionally, the low kickback chain enhances safety for the operator, making it a reliable choice for both experienced users and novices.

Innovative technologies incorporated into the McCulloch 96041011501 further enhance its performance and usability. The Easy Start system simplifies the starting process, reducing the physical strain on the user. This feature is particularly advantageous for those who may need to start the saw multiple times during a job. The anti-vibration system significantly reduces user fatigue, allowing for longer operating periods without discomfort.

Safety remains a top priority in the design of this chainsaw. Equipped with a chain brake, the McCulloch 96041011501 ensures that users have an additional layer of protection against accidental chain movement. The ergonomic handle design not only promotes comfort but also provides a secure grip, further increasing user safety.

In summary, the McCulloch 96041011501,532 42 27-27 Rev. 2 is a formidable tool in the realm of chainsaws. With its combination of powerful performance, innovative features, and user-centric design, this model stands out as an excellent choice for anyone in need of a reliable, efficient, and safe chainsaw for their outdoor cutting tasks. Whether for professional use or home maintenance, the McCulloch 96041011501 is a testament to quality engineering and practical functionality.