McCulloch 96041011501 Tools Required for Assembly, Toremovetractorfromcarton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

5/16" wrench

Utility knife

(2)

7/16" wrenches

Tire pressure gauge

(2) 1/2" wrenches

Pliers

(1)

9/16" wrench

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TOREMOVETRACTORFROMCARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

•Lift seat to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

•For battery and battery cable installation see "RE- PLACING BATTERY" in the "Service and Adjustments" section in this manual.

LABEL

Fig. 1

TO INSTALL STEERING WHEEL (See Fig. 2)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, lock washer, hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

 

INSERT

 

 

BOLT

 

 

LOCK

 

 

WASHER

 

 

LARGE FLAT

 

 

WASHER

STEERING

 

 

 

 

WHEEL

 

 

STEERING BOOT

 

 

ADAPTER

TAB

 

EXTENSION

 

 

SHAFT

LOWER

 

 

STEERING

 

 

SHAFT

 

 

TAB

 

 

SLOT

 

 

Fig. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents M11577 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering WheelToremovetractorfromcarton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Operate Mower To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To Stop Mower BladesBefore Starting the Engine Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigBelts Transaxle MaintenanceEngine LubricationAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX10.29.09 BM

532 42 27-27 Rev. 2, 96041011501 specifications

The McCulloch 96041011501,532 42 27-27 Rev. 2 is a standout model within the McCulloch line of outdoor power equipment, known for its robust design and high-performance features. As a chain saw primarily aimed at professionals and dedicated homeowners, this model delivers an exceptional balance of power, precision, and user convenience.

One of the key features of the McCulloch 96041011501 is its powerful engine, which boasts a striking performance capability. With a robust engine displacement, this chainsaw is equipped to handle a variety of cutting tasks, from felling large trees to trimming branches with ease. The engine's design emphasizes fuel efficiency, helping users maximize their productivity while minimizing fuel consumption.

The 42 cm (16.5 inches) guide bar provides a perfect balance between maneuverability and cutting capacity. It allows for precise cuts in tight spaces while maintaining efficiency during larger cuts. The chain used in this model has been engineered for rapid cutting, ensuring that users can tackle tough jobs without excessive effort. Additionally, the low kickback chain enhances safety for the operator, making it a reliable choice for both experienced users and novices.

Innovative technologies incorporated into the McCulloch 96041011501 further enhance its performance and usability. The Easy Start system simplifies the starting process, reducing the physical strain on the user. This feature is particularly advantageous for those who may need to start the saw multiple times during a job. The anti-vibration system significantly reduces user fatigue, allowing for longer operating periods without discomfort.

Safety remains a top priority in the design of this chainsaw. Equipped with a chain brake, the McCulloch 96041011501 ensures that users have an additional layer of protection against accidental chain movement. The ergonomic handle design not only promotes comfort but also provides a secure grip, further increasing user safety.

In summary, the McCulloch 96041011501,532 42 27-27 Rev. 2 is a formidable tool in the realm of chainsaws. With its combination of powerful performance, innovative features, and user-centric design, this model stands out as an excellent choice for anyone in need of a reliable, efficient, and safe chainsaw for their outdoor cutting tasks. Whether for professional use or home maintenance, the McCulloch 96041011501 is a testament to quality engineering and practical functionality.
Top Page Image Contents