McCulloch 96041011501, 532 42 27-27 Rev. 2 To Level Mower, Visual SIDE-TO-SIDE Adjustment See Fig

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 25)

•With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

•With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower LH side of mower, or, to the right to raise LH side of mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

02948

 

FIG. 25

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 26)

•With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blade is sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to its highest position.

•At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

FIG. 26

•If adjustment is necessary, see step in Visual Adjust- ment instructions above.

•Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 27 & 28) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 3/8" lower than the rear tip when the mower is in its highest position.

CAUTION: Blade is sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to highest position.

•Position blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

BB

FIG. 27

•If front tip of blade is not 1/8" to 3/8" lower than the rear tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (ltighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

B

A

TIGHTEN ADJUST

LOOSEN

ADJUST NUT

NUT B TO RAISE

B TO LOWER

MOWER

 

02950

MOWER

 

LOOSEN JAM NUT A FIRST

 

FIG. 28

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 3/8" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents M11577 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering WheelAssembly Tools Required for AssemblyToremovetractorfromcarton Before Removing Tractor from SkidInstall Seat See Fig Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Attachment Clutch Switch Disengaged EngagedTo SET Parking Brake See Fig Stopping See FigTo Adjust Mower Cutting Height See Fig To Move Forward and Backward See FigTo Operate Mower To Stop Mower BladesBefore Starting the Engine Mowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigTransaxle Maintenance EngineBelts LubricationCleaning Clean AIR ScreenAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX10.29.09 BM

532 42 27-27 Rev. 2, 96041011501 specifications

The McCulloch 96041011501,532 42 27-27 Rev. 2 is a standout model within the McCulloch line of outdoor power equipment, known for its robust design and high-performance features. As a chain saw primarily aimed at professionals and dedicated homeowners, this model delivers an exceptional balance of power, precision, and user convenience.

One of the key features of the McCulloch 96041011501 is its powerful engine, which boasts a striking performance capability. With a robust engine displacement, this chainsaw is equipped to handle a variety of cutting tasks, from felling large trees to trimming branches with ease. The engine's design emphasizes fuel efficiency, helping users maximize their productivity while minimizing fuel consumption.

The 42 cm (16.5 inches) guide bar provides a perfect balance between maneuverability and cutting capacity. It allows for precise cuts in tight spaces while maintaining efficiency during larger cuts. The chain used in this model has been engineered for rapid cutting, ensuring that users can tackle tough jobs without excessive effort. Additionally, the low kickback chain enhances safety for the operator, making it a reliable choice for both experienced users and novices.

Innovative technologies incorporated into the McCulloch 96041011501 further enhance its performance and usability. The Easy Start system simplifies the starting process, reducing the physical strain on the user. This feature is particularly advantageous for those who may need to start the saw multiple times during a job. The anti-vibration system significantly reduces user fatigue, allowing for longer operating periods without discomfort.

Safety remains a top priority in the design of this chainsaw. Equipped with a chain brake, the McCulloch 96041011501 ensures that users have an additional layer of protection against accidental chain movement. The ergonomic handle design not only promotes comfort but also provides a secure grip, further increasing user safety.

In summary, the McCulloch 96041011501,532 42 27-27 Rev. 2 is a formidable tool in the realm of chainsaws. With its combination of powerful performance, innovative features, and user-centric design, this model stands out as an excellent choice for anyone in need of a reliable, efficient, and safe chainsaw for their outdoor cutting tasks. Whether for professional use or home maintenance, the McCulloch 96041011501 is a testament to quality engineering and practical functionality.
Top Page Image Contents