McCulloch 532 40 80-72 manual HOW to USE Your Tractor

Page 10

OPERATION

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig. 5)

Your tractor is equipped with an operator presence sens- ing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

Depress clutch/brake pedal into full “BRAKE” position and hold.

Place parking brake lever in “ENGAGED” position and release pressure from clutch/brake pedal. Pedal should remain in “BRAKE” position. Make sure parking brake will hold tractor secure.

 

ATTACHMENT CLUTCH

 

LEVER "ENGAGED"

 

POSITION

THROTTLE/

IGNITION KEY

 

CHOKE

"DISENGAGED"

CONTROL

LEVER

POSITION

 

PARKING BRAKE

"BRAKE"

"ENGAGED"

POSITION

POSITION

 

GEAR SHIFT

CLUTCH/BRAKE

LEVER

PARKING BRAKE

PEDAL "DRIVE"

"DISENGAGED"

POSITION

POSITION

 

FIG. 5

STOPPING (See Fig. 5)

MOWER BLADES -

To stop mower blades,move attachment clutch lever to “DISENGAGED” position.

GROUND DRIVE -

To stop ground drive, depress clutch/brake pedal into full “BRAKE” position.

Move gearshift lever to neutral position.

ENGINE -

Move throttle control between half and full speed (fast) position.

NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping may cause engine to “backfire”.

Turn ignition key to “OFF” position and remove key. Always remove key when leaving tractor to prevent unauthorized use.

Never use choke to stop engine.

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, al- ways stop engine when stopping tractor on grass areas.

CAUTION: Always stop tractor com- pletely, as described above, before leav- ing the operator's position; to empty grass catcher, etc.

TO USE THROTTLE CONTROL (See Fig. 5)

Always operate engine at full throttle.

Operating engine at less than full throttle reduces the battery charging rate.

Full throttle offers the best bagging and mower perfor- mance.

TO MOVE FORWARD AND BACKWARD (See Fig. 5)

The direction and speed of movement is controlled by the gearshift lever.

Start tractor with clutch/brake pedal depressed and gearshift lever in neutral position.

Move gearshift lever to desired position.

Slowly release clutch/brake pedal to start move- ment.

IMPORTANT: BRING TRACTOR TO A COMPLETE STOP BEFORE SHIFTING OR CHANGING GEARS. FAILURE TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR TRANSAXLE.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 5)

The position of the attachment lift lever determines the cutting height.

Grasp lift lever.

Press plunger with thumb and move lever to desired position.

The cutting height range is approximately 1-1/2 to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD).

10

Image 10
Contents Model NO. M13538 13.5 HP 38 Inch Lawn Tractor General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Deck Levelness Check Battery See FigCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine ADD Gasoline Mowing TipsTo Start Engine See Fig Maintenance Lubrication ChartTractor Blade Removal See FigBelts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Replace Motion Drive Belt See FigReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

532 40 80-72 specifications

The McCulloch 532 40 80-72 is a standout model in the realm of garden and lawn care equipment, known for its power, efficiency, and user-friendly features. Designed for homeowners and professional landscapers alike, this versatile tool is equipped to handle a wide range of outdoor tasks, making it an essential addition to any gardening arsenal.

At the heart of the McCulloch 532 40 80-72 is a robust engine that delivers reliable performance. This powerful, two-stroke engine is designed for high efficiency, providing ample cutting power while maintaining lower fuel consumption. This not only ensures longer operational periods but also contributes to a more environmentally friendly approach to yard maintenance. The engine is optimized for reduced emissions, complying with modern environmental regulations without sacrificing performance.

One of the remarkable features of the McCulloch 532 40 80-72 is its ergonomic design. The machine boasts a comfortable grip handle that reduces fatigue during prolonged use. With an adjustable handle height, it caters to users of varying heights, allowing for a more personalized and comfortable experience. This attention to ergonomics ensures that users can manage their lawn care tasks with less strain, promoting productivity and ease of use.

Additionally, the cutting deck of the McCulloch 532 40 80-72 is engineered for durability and precision. The high-quality steel construction offers exceptional strength, while the design allows for efficient grass collection and even cutting. With adjustable cutting heights, users can customize the grass length to their preferences, enabling them to achieve a well-manicured lawn effortlessly.

Another noteworthy aspect of this model is its innovative starting system. Equipped with a reliable pull-start mechanism, the McCulloch 532 40 80-72 ensures quick and easy starts, even in cold weather conditions. This feature is particularly beneficial for those who need to get their outdoor tasks done swiftly, minimizing downtime and maximizing efficiency.

The self-propelled functionality adds an extra layer of convenience, allowing users to maneuver the mower with ease across varying terrain types. This feature not only reduces the physical effort required but also enhances the overall mowing experience.

In summary, the McCulloch 532 40 80-72 combines power, durability, and user-friendly features to create a high-performing lawn care solution. Its efficient engine, ergonomic design, durable cutting deck, and easy starting system make it a reliable choice for anyone seeking to maintain their outdoor spaces efficiently and effectively. Whether for occasional yard work or regular maintenance, the McCulloch 532 40 80-72 stands out as an exemplary tool in modern lawn care technology.