McCulloch 532 40 80-72 manual Engine, Battery, Belts, Transaxle Cooling, Lubrication

Page 15

MAINTENANCE

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE:Theoriginalequipmentbatteryonyourtractorismain- tenance free. Do not attempt to open or remove caps or cov- ers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY” in the Service and Adjustment section of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which can restrict cooling.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

SAE 30

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

-20

0

 

 

30 32 40

 

60

80

100

C

-30

-20

-10

0

10

20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, they will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the tractor is not used for 25 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Figs. 9 and 10)

Determine temperature range expected before oil change. All oil must meet API service classification SG-SL.

•Be sure tractor is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

•Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

•Remove yellow cap from end of drain valve and install the drain tube onto the fitting.

•Unlock drain valve by pushing inward and turning counterclockwise.

•To open, pull out on the drain valve.

•After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

 

OIL DRAIN VALVE

CLOSED

 

AND

 

LOCKED

 

POSITION

 

YELLOW CAP

DRAIN

TUBE

 

FIG. 10

• Remove the drain tube and replace the cap onto to the

bottom fitting of the drain valve.

• Refill engine with oil through oil fill dipstick tube. Pour

slowly. Do not overfill. For approximate capacity see

“PRODUCT SPECIFICATIONS” section of this manual.

• Use gauge on oil fill cap/dipstick for checking level.

For accurate reading, insert dipstick into the tube and

FIG. 9

oil_visc_chart1_e

push down firmly into place before removing. Keep

oil up to, but not over, the “FULL” line on dipstick.

Push dipstick down firmly into the tube when finished.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. M13538 13.5 HP 38 Inch Lawn Tractor II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Battery See FigCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips ADD GasolineTo Start Engine See Fig Lubrication Chart MaintenanceBlade Removal See Fig TractorTransaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Adjust Steering Wheel Alignment Replacing Battery See FigsTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

532 40 80-72 specifications

The McCulloch 532 40 80-72 is a standout model in the realm of garden and lawn care equipment, known for its power, efficiency, and user-friendly features. Designed for homeowners and professional landscapers alike, this versatile tool is equipped to handle a wide range of outdoor tasks, making it an essential addition to any gardening arsenal.

At the heart of the McCulloch 532 40 80-72 is a robust engine that delivers reliable performance. This powerful, two-stroke engine is designed for high efficiency, providing ample cutting power while maintaining lower fuel consumption. This not only ensures longer operational periods but also contributes to a more environmentally friendly approach to yard maintenance. The engine is optimized for reduced emissions, complying with modern environmental regulations without sacrificing performance.

One of the remarkable features of the McCulloch 532 40 80-72 is its ergonomic design. The machine boasts a comfortable grip handle that reduces fatigue during prolonged use. With an adjustable handle height, it caters to users of varying heights, allowing for a more personalized and comfortable experience. This attention to ergonomics ensures that users can manage their lawn care tasks with less strain, promoting productivity and ease of use.

Additionally, the cutting deck of the McCulloch 532 40 80-72 is engineered for durability and precision. The high-quality steel construction offers exceptional strength, while the design allows for efficient grass collection and even cutting. With adjustable cutting heights, users can customize the grass length to their preferences, enabling them to achieve a well-manicured lawn effortlessly.

Another noteworthy aspect of this model is its innovative starting system. Equipped with a reliable pull-start mechanism, the McCulloch 532 40 80-72 ensures quick and easy starts, even in cold weather conditions. This feature is particularly beneficial for those who need to get their outdoor tasks done swiftly, minimizing downtime and maximizing efficiency.

The self-propelled functionality adds an extra layer of convenience, allowing users to maneuver the mower with ease across varying terrain types. This feature not only reduces the physical effort required but also enhances the overall mowing experience.

In summary, the McCulloch 532 40 80-72 combines power, durability, and user-friendly features to create a high-performing lawn care solution. Its efficient engine, ergonomic design, durable cutting deck, and easy starting system make it a reliable choice for anyone seeking to maintain their outdoor spaces efficiently and effectively. Whether for occasional yard work or regular maintenance, the McCulloch 532 40 80-72 stands out as an exemplary tool in modern lawn care technology.
Top Page Image Contents