..... | i | , , i | i, | ,, iii | i,,11,,,1111 | L | ,i |
OPERATION
i | ii | i, i ,11, i | i,, |
TO START ENGIN _= (See Fig. 9)
When starting engine for the first time or if engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine,
oDepress clutch/brake pedal and set parking brake. o Place gearshift lever in neutral (N) position_
o Move attachment clutch to "DISENGAGED" position.
oMove throttle control lever to choke (N) position for ccldengine start. Forwarmenginestart, movethrottte control to fast (,_) position.,
=Insertkey into ignitionand turn keyclocfw_iseto"START" position and release key as soon as engine starts. Do not run starter continuously for more than fifteen
seconds per minute.. If engine does not start after several attempts, move throttle control to fast (,_) position, wait a few minutes and try again.
oWhen engine starts, move throttle control to desired position°
oAllow engine to warm up for'a few minutes before engaging drive or'attachments_
NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32°F), the carburetor fuel mixture may need to be adjusted for best engine performance. See
"TO ADJUST CARBURETOR" in the Service and Adjust- ments section of this manual.
MOWING TUPS
•Tire chains cannot be used when the mower housing is attached to tractor.
o
=The left hand side of mower'should be used for trim- ming.
. Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of
clippings and more uniform cutting..
°When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc,. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig_ 11 )o
oIf grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.
oDo not mow grass when it is Wetr. Wet grass will plug mower and leave undesirable clumps° Allow grass t,._ dry before rnowing_
oAlways operate engine at full throttle when mowing to assure better mowing performance and proper dis- charge of material Regulate ground speed by select- ing a low enough gear to give the mower cutting performance as well as the quality of cut desired.
°When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used°
f
r
FIG, 11
IVIULCHJNG iVtOWING TiPS
IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF
°The special mulching blade will recut the grass clip- pings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed_ Also, the mulched grass will biodegrade quickly to provide nutrients for'the lawn. Always mulch with your highest engine (blade) speed as this wilt provide the best recutting action ot the biades.
. Avoid cutting your lawn when | it is weL | Wet grass tends |
to form clumps and interferes | with the | mulching action° |
The best time to mow your Dawnis the early afternoon. At this time the grass has dried and the newly cut area will not be exposed to the direct sun.
-For best results, adjust the mower cutting height so that the mower cuts off only the top
oCertain types of grass and grass conditions may re- quire that an area be mulched a second time to com- pletely hide the clippings. When doing a second cut, mow across or perpendicular to the first cut path,
oChange your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn.
MAX 1/3
FIG. t2
"l 4.