|
|
|
|
|
|
|
| HI"'II!IIII' IIl'lm'l II |
|
|
|
| i1,,111 ,,,i, |
| ||
|
|
|
|
|
|
|
|
| ASSEMBLY |
|
|
|
| |||
|
|
|
|
|
|
|
|
| INI, i,i ,i, |
|
|
|
|
|
| |
INSTALL | MOWER | AND | DRIVE BELT | (See | • Place | the | R.H. suspension arm | on outward | pointing | |||||||
Figs. | 4 and | 7) |
|
|
|
|
|
| deck | pin. | If necessary, rock and | raise front | of mower | |||
|
|
|
|
|
|
|
|
|
|
|
| to align deck pin with the hole in suspension arm, | ||||
Be sure | tractor | is on level su trace and mower suspension |
| Retain with double Ioop retainer spring with loops down | ||||||||||||
arms are raised with attachment | lift control | Engage | park- | ° | as shown, |
|
|
| ||||||||
ing brake° |
|
|
|
|
|
|
| Connect | ||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
o | Cut | and remove | ties securing | bar and belts |
| footrest and retain with double loop retainer spring. | ||||||||||
| Swing | bar to left side of mower deck. |
| . | Turn height adjustment knob clockwise to remove | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
,, | Slide | mower under tractor with discharge | guard to right | . | slack from | mower suspension.. |
|
| ||||||||
| side | of | tractor, |
|
|
|
|
| Raise mower to highest position.. |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES. INSTALL BELT INTO
ELECTRIC CLUTCH PULLEY GROOVE,
oInstall one front link in top hole of the R.H. front mower bracket and R.Hofront suspension bracket,. Retain with two single loop retainer springs as shown.
oInstall second front link in Loll. front suspension bracket
only and retain with single loop retainer spring as shown..
oTurn height adjustment knob counterclocloNise until it stops.
o
Assemble gauge wheels (See "TO ADJUST GAUGE WHEELS" in the Operation section of this manual).
CHECK MOWER LEVELNESS
For best cutting results, mower should be properly leveled. See "TO LEVEL MOWER HOUSING" in the Service and
Adjustments section of this manual.
CHECK FOR PROPER POSITION OF ALL BELTS
• | Lower mower linkage with attachment lift control | See the figures that are shown for replacing motion, mower | |||||||
drive, and mower blade drive belts in the Service and | |||||||||
• | Place the L.H | suspension | arm | on outward | pointing | ||||
Adjustments section of this manual. | Verify that the belts | ||||||||
| deck pin, If necessary, rock and raise front of mower | are routed correctly |
| ||||||
| to align deck pin with the hole in suspension arm. |
| |||||||
|
|
| |||||||
| Retain with double loop retainer spring with loops down |
| FRONT | ||||||
| as shown, |
|
|
|
|
|
| ||
o | Slide left side of mower back and install | the unattached |
| SUSPENSION | |||||
ELECTRIC | BRACKETS | ||||||||
| front link in top | hole of the | LH | front mower | bracket. | CLUTCH |
| ||
| Retain with singte loop retainer | spring | as shown. | PULLEY |
| ||||
|
|
| DOUBLE | LOOP | SUSPENSION |
| |||
|
|
| ARMS | FRONT |
| ||||
|
|
| RETAINER | SPRING |
| ||||
|
|
| MOWER |
| |||||
|
| CHASSIS | (outward | pointing |
|
| |||
|
|
| BRACKET |
| |||||
|
| BRACKET | deck pins) |
|
|
| |||
|
|
|
|
|
| ||||
FRONT , LINK
SHOULDER
BOLT
SINGLE
LOOP
RETAINER
GAUGE
SPRINGS
WHEEL3/8-16
CENTER
LOCKNUT
3/8 WASHER
DOUBLELOOP
RETAINER
SPRINGANTi-SWAY
BAR
USE PLIERS FOR
RETAINER SPRINGS
IDLER/ |
|
PULLEY | DISCHARGE GUARD |
|
FIG. 4
9